Search Results

Style 580 Square O-rings are circular elastomeric rings that create a seal between two or more parts. They are made from a variety of materials, including BUNA-N rubber, and are used in a variety of industries, including automotive, aerospace, and manufacturing.

Buna-N Rubber Material | 4 1/2 in Nominal Inner Diameter | 3/16 in Cross Section | Square O-ring

Features

• Pressure range varies according to diametral clearance
• Temperature range of -40 °F to -240 °F

Molded from filled PTFE and machined to close tolerances, these seals feature low friction and excellent wear characteristics. Nitrile rings are used for energizers.

70A Durometer | PTFE Material | 52 MM Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities

Utilizing a sturdy metal case, these wipers are molded from the same high performance urethane used in our Heavy Duty U-seals. Built for severe service, these wipers are capable of surviving hostile environments.

92A Durometer | Urethane Material | 1 in Nominal Inner Diameter

Features

• Used in Heavy Duty U-seals
• Capable of surviving hostile environments
• Molded from the high performance urethane

T-Seals combine a resilient sealing ring with a hard, split back-up ring on each side of the sealing element. The assembly installs in a standard o-ring groove. T-Seals are non-spiraling and extrusion resistant to 5,000 psi with improved tolerances. Intermediate and Wide Base T-Seals are designed to fit MIL-5514F o-ring glands only and interchange with 1 o-ring / 1 back-up ring and 1 o-ring / 2 back-up ring grooves, respectively.

Buna-N Rubber Material | 2 1/8 in Nominal Inner Diameter | Piston T-Seal

Totally interchangeable with Style PS1400 PTFE piston seals, Style PS1500 piston seals are molded from tough 60 Shore D durometer polyurethane. During the molding process, a .002” thick band of molybdenum disulfide is molded into the outside diameter of the seal ring for reduced friction. PS1500 piston seals are easily stretched over the piston and recover rapidly with the elimination of the “cold flow” characteristics found in PTFE seals. Piston diameter “I” dimensions are given for pistons without wear rings.

60 Shore D Durometer | Polyurethane Material | 1.606 in Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities

HWT-3000X1000 has a wall thickness of 1 in. The ID is 1 in and the OD is 3 in. The material is 1026 Carbon Steel.

Heavy Wall Tubes are used for machining high strength and close tolerance parts like bushings, axles, hydraulics, and sleeves.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

Molded from 93 Shore A polyurethane with a 70 Shore A energizer, this seal utilizes the same groove dimensions as a standard o-ring or T-seal. One or two Style 575 back-up rings may be used for wider grooves. Extrusion resistant by design, this seal is also resistant to rolling and twisting. Installation is an easy two step snap-in procedure with no need to re-size before insertion into the bore. Piston diameter “I” dimensions are given for pistons without wear rings.

93A; 70A Durometer | Urethane Material | 3 5/8 in Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities

Steel Rod Clevis Mount with a 0.75 in – 16 TPI threaded end and a 0.75 in pin hole.

Clevis mounts help maintain alignment and protect the cylinder from side load. Mounts attach to threaded stud ends, pivot holes, or bolt holes on the cylinder. Can be used with hydraulic cylinders with standard bore sizes.

DUCT-10000 has a diameter of 10 in. The material is 65-45-12 Ductile Iron.

65-45-12 Ductile Iron is used to machine pistons, glands, caps, manifolds, rams, and valve bodies.

Ductile has higher machining speeds than steel and there is usually no need for deburring machined parts. The graphite flakes in the material act as a self-lubricant. Ductile can be flame or induction hardened as well as deep hardened.

Ductile bars are produced with sufficient stock on the outside diameter to ensure clean-up at the nominal dimension.

• Excellent machinability
• Optimal impact strengths
• Optimal fatigue properties
• Optimal electrical conductivity
• High magnetic permeability

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

ALHT3750X3500 has a 0.125 in wall thickness. The ID is 3.5 in and the OD is 3.75 in. The material is 6063-T832 Aluminum.

Seamless extruded and cold-drawn. Hard coated on the ID which gives the aluminum tube a tough, abrasive-resitant surface.

6063-T832 Aluminum is used for pneumatic cylinder applications requiring very good corrosion resistance and/or light weight. Can also be used for low-pressure oil cylinders (250 psi or less).

• No machining required on the ID
• Seamless extruded and cold-drawn
• Hard coated interior
• Corrosion resistance
• Good weldability

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.