Browse Categories

Search Results

Filter Your Search

Show Attribute Category Group

Shop by Category

Loading...

CIHT6250X6000 has a wall thickness of 0.125 in. The ID is 6 in and the OD is 6.25 in. The material is 1026 Carbon Steel with chrome plating on the Inside Surface.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$13.84
15-29$9.90
30-74$7.68
75+$6.92
/IN
at
Select Length
IN
-
IN

CPO-4500 has a 4.5 in diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.

ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.

  • Extremely smooth surface finish
  • Excellent wear and corrosion resistance
  • Good strength and impact properties
  • Good machinability
  • Reasonable weldability
  • Fair response to normal heat treating and induction hardening practices

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$34.00
15-29$24.31
30-59$21.25
60-119$17.00
120+$15.47
/IN
at
Select Length
IN
-
IN

Asymmetric rod seal designed with precision trimmed sealing lips to provide a dry sealing solution in light and medium-duty applications. The Hallite 605 is molded in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation and excellent low temperature performance. The twin lip design helps solve difficult rod sealing problems by providing lower friction, increased stability, and high, dynamic lip force, while preventing air penetration from outside the cylinder. Designed to have interference in the seal housing groove and has a secondary lip. The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland. The inner dynamic lip is shorter and more robust to improve sealing and compression set characteristics over conventional, symmetrical U-seals.

The seal can be considered for use in heavy-duty applications when used with a suitable full depth back-up ring. The sealing lips are precision trimmed at an angle to give optimal rod sealing performance.

94A Durometer | Urethane Material | 2 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal

Features

  • General purpose rod seal
  • Robust design
  • Excellent wear resistance
  • Increase seal stability
  • Performs well over wide temperature range and is extremely effective in low temperatures
  • Primary lip protection
  • Easy to install

$11.77
/EA
7 in Hot Finished 1018 Carbon Steel Round Bar | CRC Distribution Inc.

*
7 in Hot Finished 1018 Carbon Steel*
round bar. Material can be cut to any size.

Suitable for shafting and applications that do not require the greater strength of high carbon and alloy steels.

  • Good case hardening properties
  • Fair machinability
  • Readily brazed and welded

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-4$56.45
5-9$28.23
10-14$25.06
15+$22.58
/IN
at
Select Length
IN
-
IN
1 7/8 X 2 1/16 X 3/32 O-ring NBR70 - 568-134 | CRC Distribution Inc.

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70 Durometer | Buna-N Rubber Material | 1 7/8 in Nominal Inner Diameter | 3/32 in Cross Section | O-Ring

Features

  • Pressure range varies according to diametral clearance
  • Temperature range of -40 °F to -240 °F

$0.36
/EA
3 3/4 X 4 1/8 X 3/16 O-ring NBR70 - 568-343 | CRC Distribution Inc.

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70 Durometer | Buna-N Rubber Material | 3 3/4 in Nominal Inner Diameter | 3/16 in Cross Section | O-Ring

Features

  • Pressure range varies according to diametral clearance
  • Temperature range of -40 °F to -240 °F

$1.47
/EA

HWT-5000X3000 has a wall thickness of 1 in. The ID is 3 in and the OD is 5 in. The material is 1026 Carbon Steel.

Heavy Wall Tubes are used for machining high strength and close tolerance parts like bushings, axles, hydraulics, and sleeves.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-4$12.01
5-24$10.50
25-49$9.32
50+$8.40
/IN
at
Select Length
IN
-
IN

HWT-6000X3000 has a wall thickness of 1.5 in. The ID is 3 in and the OD is 6 in. The material is 1026 Carbon Steel.

Heavy Wall Tubes are used for machining high strength and close tolerance parts like bushings, axles, hydraulics, and sleeves.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-4$27.61
5-14$24.13
15-24$21.43
25-49$19.31
50+$17.57
/IN
at
Select Length
IN
-
IN

1 Bronze Rod Glands

$40.95
/EA

HC-4500-12 has a 5.25 in OD and is made to fit a 4 in bore cylinder.

Head cap size is determined based on the bending stress.

A static seal or o-ring is used in between the head cap and barrel (except welded construction).

The main function of the head cap is to enclose the pressure chamber at one end. The cap is connected to the cylinder body by means of welding, threading, bolts, or tie rod.

$82.30
/PC
  • « PREV
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • NEXT »