Browse Categories

Search Results

Filter Your Search

Show Attribute Category Group

Shop by Category

Loading...
1 3/8 X 1 5/8 X 1/8 O-ring NBR70 - 568-220 | CRC Distribution Inc.

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70 Durometer | Buna-N Rubber Material | 1 3/8 in Nominal Inner Diameter | 1/8 in Cross Section | O-Ring

Features

  • Pressure range varies according to diametral clearance
  • Temperature range of -40 °F to -240 °F

$0.28
/EA

Parback® backup ring with a curved cross-section.

Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.

90A Durometer | Buna-N Rubber Material | 3 in Nominal Inner Diameter | 1/8 in Cross Section | Backup Ring

Features

  • Excellent extrusion resistance
  • Easily stretched for installation
  • Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces

$1.61
/EA

MHT-110X134 has a wall thickness of 12 mm. The ID is 110 mm and the OD is 134 mm. The material is 1026 Carbon Steel and has been stress-relieved and annealed.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$14.49
15-44$11.25
45-104$10.13
105+$9.22
/IN
at
Select Length
IN
-
IN

MHT-80X95 has a wall thickness of 7.5 mm. The ID is 80 mm and the OD is 95 mm. The material is 1026 Carbon Steel and has been stress-relieved and annealed.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$7.10
15-74$5.51
75-104$4.97
105+$4.52
/IN
at
Select Length
IN
-
IN
Light Duty Snap-in Wiper | CRC Distribution Inc.

This light duty wiper is molded in polyurethane and features a double-stepped shoulder to fit tightly in the gland throat.

Urethane Material | 36 MM Inner Diameter | Wiper

Features

  • Double-stepped shoulder

$3.00
/EA

ALHT3250X3000 has a 0.125 in wall thickness. The ID is 3 in and the OD is 3.25 in. The material is 6063-T832 Aluminum.

Seamless extruded and cold-drawn. Hard coated on the ID which gives the aluminum tube a tough, abrasive-resitant surface.

6063-T832 Aluminum is used for pneumatic cylinder applications requiring very good corrosion resistance and/or light weight. Can also be used for low-pressure oil cylinders (250 psi or less).

  • No machining required on the ID
  • Seamless extruded and cold-drawn
  • Hard coated interior
  • Corrosion resistance
  • Good weldability

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$5.88
15-29$4.70
30-104$3.36
105+$2.61
/IN
at
Select Length
IN
-
IN

Asymmetric rod seal designed with precision trimmed sealing lips to provide a dry sealing solution in light and medium-duty applications. The Hallite 605 is molded in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation and excellent low temperature performance. The twin lip design helps solve difficult rod sealing problems by providing lower friction, increased stability, and high, dynamic lip force, while preventing air penetration from outside the cylinder. Designed to have interference in the seal housing groove and has a secondary lip. The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland. The inner dynamic lip is shorter and more robust to improve sealing and compression set characteristics over conventional, symmetrical U-seals.

The seal can be considered for use in heavy-duty applications when used with a suitable full depth back-up ring. The sealing lips are precision trimmed at an angle to give optimal rod sealing performance.

94A Durometer | Urethane Material | 1 1/2 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal

Features

  • General purpose rod seal
  • Robust design
  • Excellent wear resistance
  • Increase seal stability
  • Performs well over wide temperature range and is extremely effective in low temperatures
  • Primary lip protection
  • Easy to install

$10.63
/EA
2 X 2 3/8 X 3/16 O-ring NBR70 (20) - 568-329 | CRC Distribution Inc.

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70 Durometer | Buna-N Rubber Material | 2 in Nominal Inner Diameter | 3/16 in Cross Section | O-Ring

Features

  • Pressure range varies according to diametral clearance
  • Temperature range of -40 °F to -240 °F

$0.62
/EA
PS, 2.000 X 1.608 X 0.129 URE - PS1500-32 | CRC Distribution Inc.

Totally interchangeable with Style PS1400 PTFE piston seals, Style PS1500 piston seals are molded from tough 60 Shore D durometer polyurethane. During the molding process, a .002” thick band of molybdenum disulfide is molded into the outside diameter of the seal ring for reduced friction. PS1500 piston seals are easily stretched over the piston and recover rapidly with the elimination of the “cold flow” characteristics found in PTFE seals. Piston diameter “I” dimensions are given for pistons without wear rings.

60 Shore D Durometer | Polyurethane Material | 1.606 in Nominal Inner Diameter | Piston Seal

Features

  • Easy assembly
  • Low friction capabilities

$5.82
/EA

0.500 3000 PSI NPT PORTS

$4.11
/PC
  • « PREV
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • NEXT »