Search Results
Filter Your Search
Shop by Category
Molded from 93 Shore A polyurethane with a 70 Shore A energizer, this seal utilizes the same groove dimensions as a standard o-ring or T-seal. One or two Style 575 back-up rings may be used for wider grooves. Extrusion resistant by design, this seal is also resistant to rolling and twisting. Installation is an easy two step snap-in procedure with no need to re-size before insertion into the bore. Piston diameter “I” dimensions are given for pistons without wear rings.
93A; 70A Durometer | Urethane Material | 2 5/8 in Nominal Inner Diameter | Piston Seal
Features
- Easy assembly
- Low friction capabilities
MCPO-85 has a 85 mm diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.
ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.
- Extremely smooth surface finish
- Excellent wear and corrosion resistance
- Good strength and impact properties
- Good machinability
- Reasonable weldability
- Fair response to normal heat treating and induction hardening practices
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
1-29 | $19.92 |
30-59 | $14.24 |
60-119 | $11.06 |
120-287 | $9.96 |
288+ | $9.06 |
O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.
70 Durometer | Buna-N Rubber Material | 5 in Nominal Inner Diameter | 3/32 in Cross Section | O-Ring
Features
- Pressure range varies according to diametral clearance
- Temperature range of -40 °F to -240 °F
O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.
70 Durometer | Buna-N Rubber Material | 2 7/8 in Nominal Inner Diameter | 3/16 in Cross Section | O-Ring
Features
- Pressure range varies according to diametral clearance
- Temperature range of -40 °F to -240 °F
CIHT6375X6000 has a wall thickness of 0.1875 in. The ID is 6 in and the OD is 6.375 in. The material is 1026 Carbon Steel with chrome plating on the Inside Surface.
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
1-14 | $11.18 |
15-74 | $9.92 |
75-104 | $8.94 |
105+ | $8.14 |
MCPO-14 has a 14 mm diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.
ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.
- Extremely smooth surface finish
- Excellent wear and corrosion resistance
- Good strength and impact properties
- Good machinability
- Reasonable weldability
- Fair response to normal heat treating and induction hardening practices
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
1-29 | $3.03 |
30-59 | $1.52 |
60-89 | $1.30 |
90-134 | $1.01 |
135+ | $0.91 |
Molded from filled PTFE and machined to close tolerances, these seals feature low friction and excellent wear characteristics. Nitrile rings are used for energizers.
70A Durometer | PTFE Material | 52 MM Nominal Inner Diameter | Piston Seal
Features
- Easy assembly
- Low friction capabilities
T-Seals combine a resilient sealing ring with a hard, split back-up ring on each side of the sealing element. The assembly installs in a standard o-ring groove. T-Seals are non-spiraling and extrusion resistant to 5,000 psi with improved tolerances. Intermediate and Wide Base T-Seals are designed to fit MIL-5514F o-ring glands only and interchange with 1 o-ring / 1 back-up ring and 1 o-ring / 2 back-up ring grooves, respectively.
Buna-N Rubber Material | 2 1/8 in Nominal Inner Diameter | Piston T-Seal
Steel Rod Clevis Mount with a 0.75 in – 16 TPI threaded end and a 0.75 in pin hole.
Clevis mounts help maintain alignment and protect the cylinder from side load. Mounts attach to threaded stud ends, pivot holes, or bolt holes on the cylinder. Can be used with hydraulic cylinders with standard bore sizes.