Search Results

1 in clevis pin with two 0.140 in holes that can be used to retain the pin with cotter pins or locking pins. Cotter pins not included.

Parback® backup ring with a curved cross-section.

Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.

90A Durometer | Buna-N Rubber Material | 4 5/8 in Nominal Inner Diameter | 3/16 in Cross Section | Backup Ring

Features

• Excellent extrusion resistance
• Easily stretched for installation
• Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces

Style ST wiper rings are precision molded from 90A durometer urethane. Flexible enough to easily snap into a groove yet tough enough to handle difficult rod wiping applications. “V” tagged wipers are constructed of fluorocarbon.

90A Durometer | Urethane Material | 1 1/8 in Nominal Inner Diameter

Features

• Flexible enough to snap into a groove
• Wipers are constructed of fluorocarbon

HWT-4500X2500 has a wall thickness of 1 in. The ID is 2.5 in and the OD is 4.5 in. The material is 1026 Carbon Steel.

Heavy Wall Tubes are used for machining high strength and close tolerance parts like bushings, axles, hydraulics, and sleeves.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

HWT-5500X3000 has a wall thickness of 1.25 in. The ID is 3 in and the OD is 5.5 in. The material is 1026 Carbon Steel.

Heavy Wall Tubes are used for machining high strength and close tolerance parts like bushings, axles, hydraulics, and sleeves.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

Molded in urethane, this wiper is flexible enough to easily snap into a groove yet tough enough to handle difficult rod wiping applications.

Urethane Material | 45 MM Inner Diameter | Wiper

Utilizing tough polyurethane, these seals possess excellent wear and abrasion resistance. Symmetrical in design, they can be used in rod or piston applications. E= European Urethane.

Urethane Material | 35 MM Nominal Inner Diameter | U-Seal

Style 850 u-seals offer excellent resistance to extrusion and abrasion. The round cross-section expander offers energized sealing from zero to 5,000 psi.

95A Durometer | Urethane Material | 2 3/4 in Nominal Inner Diameter | 7/32 in Cross Section | U-Seal

Utilizing a sturdy metal case, these wipers are molded from the same high performance urethane used in our Heavy Duty U-seals. Built for severe service, these wipers are capable of surviving hostile environments.

92A Durometer | Urethane Material | 2 1/2 in Nominal Inner Diameter

Features

• Used in Heavy Duty U-seals
• Capable of surviving hostile environments
• Molded from the high performance urethane

Molded from 93 Shore A polyurethane with a 70 Shore A energizer, this seal utilizes the same groove dimensions as a standard o-ring or T-seal. One or two Style 575 back-up rings may be used for wider grooves. Extrusion resistant by design, this seal is also resistant to rolling and twisting. Installation is an easy two step snap-in procedure with no need to re-size before insertion into the bore. Piston diameter “I” dimensions are given for pistons without wear rings.

93A; 70A Durometer | Urethane Material | 2 1/8 in Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities