Search Results

HWT-6500X4000 has a wall thickness of 1.25 in. The ID is 4 in and the OD is 6.5 in. The material is 1026 Carbon Steel.

Heavy Wall Tubes are used for machining high strength and close tolerance parts like bushings, axles, hydraulics, and sleeves.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

Asymmetric rod seal designed with precision trimmed sealing lips to provide a dry sealing solution in light and medium-duty applications. The Hallite 605 is molded in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation and excellent low temperature performance. The twin lip design helps solve difficult rod sealing problems by providing lower friction, increased stability, and high, dynamic lip force, while preventing air penetration from outside the cylinder. Designed to have interference in the seal housing groove and has a secondary lip. The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland. The inner dynamic lip is shorter and more robust to improve sealing and compression set characteristics over conventional, symmetrical U-seals.

The seal can be considered for use in heavy-duty applications when used with a suitable full depth back-up ring. The sealing lips are precision trimmed at an angle to give optimal rod sealing performance.

94A Durometer | Urethane Material | 3/4 in Nominal Inner Diameter | 1/8 in Cross Section | U-Seal

Features

• General purpose rod seal
• Robust design
• Excellent wear resistance
• Increase seal stability
• Performs well over wide temperature range and is extremely effective in low temperatures
• Primary lip protection
• Easy to install

Piston diameter “I” dimensions are given for pistons without wear rings.

15% Glass Filled PTFE Material | 2.603 in Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities

Rubber Material | 1 1/2 in Nominal Inner Diameter | Wiper

Rubber Material | 1 1/2 in Nominal Inner Diameter | Wiper

MHT-55X2.750 has a wall thickness of 7.425 mm. The ID is 55 mm and the OD is 69.85 mm. The material is 1026 Carbon Steel and has been stress-relieved and annealed.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

Molded in urethane, this wiper is flexible enough to easily snap into a groove yet tough enough to handle difficult rod wiping applications.

Urethane Material | 35 MM Inner Diameter | Wiper

O-ring

O-Ring

CPO-4000 has a 4 in diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.

ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.

• Extremely smooth surface finish
• Excellent wear and corrosion resistance
• Good strength and impact properties
• Good machinability
• Reasonable weldability
• Fair response to normal heat treating and induction hardening practices

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

Style ST-XL wipers are molded from premium urethane and are direct replacements for Style “ST” or “D” wipers. The outside diameter of the ring has a crush lip providing extra interference in the groove. A bead on the shoulder stops contaminates from entering through the groove. The inside diameter is ribbed to prevent pressure traps between the wiper and rod seal.

94A Durometer | Urethane Material | 4 in Nominal Inner Diameter

Features

• Crush lip to provide extra interference
• Bead on the shoulder to keep contaminants out
• Ribbed ID to prevent pressure traps

Style 850 u-seals offer excellent resistance to extrusion and abrasion. The round cross-section expander offers energized sealing from zero to 5,000 psi.

95A Durometer | Urethane Material | 2 1/2 in Nominal Inner Diameter | 7/32 in Cross Section | U-Seal