Search Results
Filter Your Search
Shop by Category
O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.
70 Durometer | Buna-N Rubber Material | 3 3/8 in Nominal Inner Diameter | 3/16 in Cross Section | O-Ring
Features
- Pressure range varies according to diametral clearance
- Temperature range of -40 °F to -240 °F
HT-4000X3000 has a wall thickness of 0.5 in. The ID is 3 in and the OD is 4 in. The material is DOM 1026 Carbon Steel and has been stress-relieved and annealed.
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
1-14 | $11.17 |
15-59 | $9.59 |
60-104 | $8.39 |
105-149 | $7.45 |
150+ | $6.71 |
HT-3000X2000 has a wall thickness of 0.5 in. The ID is 2 in and the OD is 3 in. The material is DOM 1026 Carbon Steel and has been stress-relieved and annealed.
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
1-14 | $8.14 |
15-59 | $6.99 |
60-104 | $6.11 |
105-149 | $5.43 |
150+ | $4.89 |
1 in clevis pin with 0.048 in grooves machined into each end to fit two retaining rings. Retaining rings are not included.
Pivot pins with grooves are meant to be used on a hydraulic cylinder that extends and retracts a telescoping lift arm.
HWT-8000X5000 has a wall thickness of 1.5 in. The ID is 5 in and the OD is 8 in. The material is 1026 Carbon Steel.
Heavy Wall Tubes are used for machining high strength and close tolerance parts like bushings, axles, hydraulics, and sleeves.
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
1-4 | $30.20 |
5-14 | $26.40 |
15-24 | $23.45 |
25-49 | $21.12 |
50+ | $19.22 |
SB38ES has a 1.5 in ID.
The bushing is Unsealed and made of forged steel. The ball will swivel like a fish eye with 3-5 degrees of movement.
Designed to fit on one or two piece pistons, this piston seal employs a nitrile seal for high sealability, nylon split back-ups for extrusion resistance, and two split bearing rings. No further support bearings are required.
70A Durometer | NBR Material | 34 MM Nominal Inner Diameter | Piston Seal
Features
- Easy assembly
- Low friction capabilities
The twin lip design helps solve difficult rod sealing problems by providing lower friction, increased stability, and high, dynamic lip force, while preventing air penetration from outside the cylinder.
Asymmetric rod seal designed with precision trimmed sealing lips to provide a dry sealing solution in light and medium-duty applications. The Hallite 605 is molded in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation and excellent low temperature performance.
Designed to have interference in the seal housing groove and has a secondary lip. The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland. The inner dynamic lip is shorter and more robust to improve sealing and compression set characteristics over conventional, symmetrical U-seals. The seal can be considered for use in heavy-duty applications when used with a suitable full depth back-up ring. The sealing lips are precision trimmed at an angle to give optimal rod sealing performance.
94A Durometer | Urethane Material | 3 1/2 in Nominal Inner Diameter | 1/4 in Cross Section | U-Seal
Features
- General purpose rod seal
- Robust design
- Excellent wear resistance
- Increase seal stability
- Performs well over wide temperature range and is extremely effective in low temperatures
- Primary lip protection
- Easy to install
This wear ring is molded from glass reinforced nylon. This style is highly recommended because of their wear rate and non-scoring properties and their ability to ingest metal chips.
Nylon Material | 45 MM Nominal Inner Diameter | Wear Ring
Features
- Protection Against Wear
- Reduced Friction
- Extended Cylinder Life
- Operational Efficiency
O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.
70 Durometer | Buna-N Rubber Material | 3 1/2 in Nominal Inner Diameter | 1/8 in Cross Section | O-Ring
Features
- Pressure range varies according to diametral clearance
- Temperature range of -40 °F to -240 °F