Browse Categories

Search Results

Filter Your Search

Show Attribute Category Group

Shop by Category

Loading...
3 in Bronze Bar | CRC Distribution Inc.

660-3000 has a 3 in rod diameter. The material is 660 Bronze Copper Alloy 932.

660 Bronze is known as “bearing bronze” because it is most commonly used in bushing and bearing applications. While it is easily machined, the bronze alloy is hard, strong, and resistant to wear. It is also less dependent on lubrication than other alloys and has reasonable corrosion resistance to seawater and brine.

660 Bronze is used for machining bearings, bushings, wear strips, and plates. This grade of bronze is used in pump, cylinder, and machine tool applications.

  • Good anti-friction properties
  • Ample strength and hardness
  • Adeqaute ductility
  • Excellent machinability

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-4$43.66
5-9$38.77
10-14$34.93
15+$31.79
/IN
at
Select Length
IN
-
IN

Style 850 u-seals offer excellent resistance to extrusion and abrasion. The round cross-section expander offers energized sealing from zero to 5,000 psi.

95A Durometer | Urethane Material | 2 3/4 in Nominal Inner Diameter | 7/32 in Cross Section | U-Seal

$14.20
/EA

The twin lip design helps solve difficult rod sealing problems by providing lower friction, increased stability, and high, dynamic lip force, while preventing air penetration from outside the cylinder.

Asymmetric rod seal designed with precision trimmed sealing lips to provide a dry sealing solution in light and medium-duty applications. The Hallite 605 is molded in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation and excellent low temperature performance.

Designed to have interference in the seal housing groove and has a secondary lip. The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland. The inner dynamic lip is shorter and more robust to improve sealing and compression set characteristics over conventional, symmetrical U-seals. The seal can be considered for use in heavy-duty applications when used with a suitable full depth back-up ring. The sealing lips are precision trimmed at an angle to give optimal rod sealing performance.

94A Durometer | Urethane Material | 1 1/8 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal

Features

  • General purpose rod seal
  • Robust design
  • Excellent wear resistance
  • Increase seal stability
  • Performs well over wide temperature range and is extremely effective in low temperatures
  • Primary lip protection
  • Easy to install

$9.66
/EA

HWT-3000X1500 has a wall thickness of 0.75 in. The ID is 1.5 in and the OD is 3 in. The material is 1026 Carbon Steel.

Heavy Wall Tubes are used for machining high strength and close tolerance parts like bushings, axles, hydraulics, and sleeves.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-4$5.32
5-24$4.65
25-49$4.13
50+$3.72
/IN
at
Select Length
IN
-
IN

Rubber Material | 1 1/4 in Nominal Inner Diameter | Wiper

Rubber Material | 1 1/4 in Nominal Inner Diameter | Wiper

$3.35
/EA

Female connection on both ends.

ORB fittings incorporate a port connection for leak prevention in medium and high pressure hydraulic systems. The female port has a straight thread and a machined surface, along with a chamfer where the o-ring is seated. The seal is created when the o-ring is compressed into the chamfer when mating the male and female connection providing a leak-tight seal.

$16.60
/PC
4 Bronze Rod Glands - PKH-RG-40 | CRC Distribution Inc.

4 Bronze Rod Glands

$365.51
/EA

Style 850 u-seals offer excellent resistance to extrusion and abrasion. The round cross-section expander offers energized sealing from zero to 5,000 psi.

95A Durometer | Urethane Material | 1 1/4 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal

$7.10
/EA

HT-4250X3500 has a wall thickness of 0.375 in. The ID is 3.5 in and the OD is 4.25 in. The material is DOM 1026 Steel – ST52.3 and has been stress-relieved and annealed.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$9.24
15-59$7.93
60-104$6.93
105-149$6.16
150+$5.55
/IN
at
Select Length
IN
-
IN

MHT-95X115 has a wall thickness of 10 mm. The ID is 95 mm and the OD is 115 mm. The material is 1026 Carbon Steel and has been stress-relieved and annealed.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$13.05
15-44$10.13
45-104$9.12
105+$8.30
/IN
at
Select Length
IN
-
IN
  • « PREV
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • NEXT »