Search Results
Filter Your Search
Category Group
Shop by Category
SS17-4/CPO-1250 has a 1.25 in diameter. The material is 17-4 Stainless Steel with Standard Chrome on the exterior.
Commonly used in offshore cranes, marine cylinders, and marine steering cylinders.
- Highest level of corrosion resistance
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-14 | $6.99 |
| 15-44 | $6.00 |
| 45-59 | $4.66 |
| 60-104 | $4.20 |
| 105+ | $3.82 |
HT-4000X3000 has a wall thickness of 0.5 in. The ID is 3 in and the OD is 4 in. The material is DOM 1026 Carbon Steel and has been stress-relieved and annealed.
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-14 | $11.17 |
| 15-59 | $9.59 |
| 60-104 | $8.39 |
| 105-149 | $7.45 |
| 150+ | $6.71 |
MCPO-95 has a 95 mm diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.
ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.
- Extremely smooth surface finish
- Excellent wear and corrosion resistance
- Good strength and impact properties
- Good machinability
- Reasonable weldability
- Fair response to normal heat treating and induction hardening practices
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-29 | $24.88 |
| 30-59 | $17.79 |
| 60-119 | $13.81 |
| 120-287 | $12.44 |
| 288+ | $11.32 |
O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.
70 Durometer | Buna-N Rubber Material | 3 1/2 in Nominal Inner Diameter | 1/8 in Cross Section | O-Ring
Features
- Pressure range varies according to diametral clearance
- Temperature range of -40 °F to -240 °F
Style ST-XL wipers are molded from premium urethane and are direct replacements for Style “ST” or “D” wipers. The outside diameter of the ring has a crush lip providing extra interference in the groove. A bead on the shoulder stops contaminates from entering through the groove. The inside diameter is ribbed to prevent pressure traps between the wiper and rod seal.
94A Durometer | Urethane Material | 4 1/2 in Nominal Inner Diameter
Features
- Crush lip to provide extra interference
- Bead on the shoulder to keep contaminants out
- Ribbed ID to prevent pressure traps
O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.
70 Durometer | Buna-N Rubber Material | 2 5/8 in Nominal Inner Diameter | 3/16 in Cross Section | O-Ring
Features
- Pressure range varies according to diametral clearance
- Temperature range of -40 °F to -240 °F
Wear rings provide a hard-wearing surface that protects the cylinder walls and the piston rod from scoring and abrasion. By maintaining alignment and reducing side loads, these rings facilitate smoother piston movement and lower friction levels.
Nylon Material | 2 1/2 in Nominal Inner Diameter | 1/8 in Cross Section | Wear Ring
Features
- Scarf Cut wear ring
- Protection Against Wear
- Reduced Friction
- Extended Cylinder Life
- Operational Efficiency
O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.
90 Durometer | Buna-N Rubber Material | 5/8 in Nominal Inner Diameter | 1/16 in Cross Section | O-Ring
Features
- Pressure range varies according to diametral clearance
- Temperature range of -40 °F to -240 °F
O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.
70 Durometer | Buna-N Rubber Material | 1 15/16 in Nominal Inner Diameter | 3/32 in Cross Section | O-Ring
Features
- Pressure range varies according to diametral clearance
- Temperature range of -40 °F to -240 °F
Hytrel backup ring with a flat cross-section.
Molded of 55D Durometer Hytrel, these back-up rings provide excellent extrusion resistance and tolerance to fluids such as phosphate esters, hydraulic oil and water. Stretched for installation, they return quickly to their original size for easy installation.
55D Durometer | Hytrel Material | 3 3/4 in Nominal Inner Diameter | 0.11 in Cross Section | Backup Ring
Features
- Improved extrusion resistance compared to standard FKM or NBR backups
- Can be stretched over larger diameters and will return quickly to their original size
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
