Browse Categories

Search Results

Filter Your Search

Show Attribute Category Group

Shop by Category

Loading...

Parback® backup ring with a curved cross-section.

Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.

90A Durometer | Buna-N Rubber Material | 2 1/8 in Nominal Inner Diameter | 3/16 in Cross Section | Backup Ring

Features

  • Excellent extrusion resistance
  • Easily stretched for installation
  • Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces

$1.44
/EA

CPO-2375 has a 2.375 in diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.

ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.

  • Extremely smooth surface finish
  • Excellent wear and corrosion resistance
  • Good strength and impact properties
  • Good machinability
  • Reasonable weldability
  • Fair response to normal heat treating and induction hardening practices

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-29$7.21
30-104$5.59
105-287$5.04
288+$4.59
/IN
at
Select Length
IN
-
IN

ALUM-3500 has a 3.5 in diameter. The material is 6061 Aluminum T6

6061 Aluminum T6 is suitable for machining pistons and head glands.

The T6 refers to the temper or degree of hardness. T6 has been solution heat treated and artificially aged to provide the maximum yield strength for a 6061 aluminum alloy.

  • Heat treated and aged for increased strength
  • Easily formed
  • Weldable
  • Corrosion resistant

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$11.52
15-29$8.24
30+$6.39
/IN
at
Select Length
IN
-
IN

HT-2250X1750 has a wall thickness of 0.25 in. The ID is 1.75 in and the OD is 2.25 in. The material is DOM 1026 Carbon Steel and has been stress-relieved and annealed.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$3.78
15-59$2.84
60+$2.27
/IN
at
Select Length
IN
-
IN

HWT-4500X2500 has a wall thickness of 1 in. The ID is 2.5 in and the OD is 4.5 in. The material is 1026 Carbon Steel.

Heavy Wall Tubes are used for machining high strength and close tolerance parts like bushings, axles, hydraulics, and sleeves.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-4$11.08
5-24$9.68
25-49$8.60
50+$7.75
/IN
at
Select Length
IN
-
IN

HWT-3500X1500 has a wall thickness of 1 in. The ID is 1.5 in and the OD is 3.5 in. The material is 1026 Carbon Steel.

Heavy Wall Tubes are used for machining high strength and close tolerance parts like bushings, axles, hydraulics, and sleeves.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-4$7.89
5-24$6.90
25-49$6.13
50+$5.52
/IN
at
Select Length
IN
-
IN

This wear ring is molded from glass reinforced nylon. This style is highly recommended because of their wear rate and non-scoring properties and their ability to ingest metal chips.

Nylon Material | 45 MM Nominal Inner Diameter | Wear Ring

Features

  • Protection Against Wear
  • Reduced Friction
  • Extended Cylinder Life
  • Operational Efficiency

$15.53
/EA

T-Seals combine a resilient sealing ring with a hard, split back-up ring on each side of the sealing element. The assembly installs in a standard o-ring groove. T-Seals are non-spiraling and extrusion resistant to 5,000 psi with improved tolerances. Intermediate and Wide Base T-Seals are designed to fit MIL-5514F o-ring glands only and interchange with 1 o-ring / 1 back-up ring and 1 o-ring / 2 back-up ring grooves, respectively.

Buna-N Rubber Material | 2 5/8 in Nominal Inner Diameter | Piston T-Seal

$11.73
/EA

Asymmetric rod seal designed with precision trimmed sealing lips to provide a dry sealing solution in light and medium-duty applications. The Hallite 605 is molded in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation and excellent low temperature performance. The twin lip design helps solve difficult rod sealing problems by providing lower friction, increased stability, and high, dynamic lip force, while preventing air penetration from outside the cylinder. Designed to have interference in the seal housing groove and has a secondary lip. The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland. The inner dynamic lip is shorter and more robust to improve sealing and compression set characteristics over conventional, symmetrical U-seals.

The seal can be considered for use in heavy-duty applications when used with a suitable full depth back-up ring. The sealing lips are precision trimmed at an angle to give optimal rod sealing performance.

94A Durometer | Urethane Material | 3/4 in Nominal Inner Diameter | 1/8 in Cross Section | U-Seal

Features

  • General purpose rod seal
  • Robust design
  • Excellent wear resistance
  • Increase seal stability
  • Performs well over wide temperature range and is extremely effective in low temperatures
  • Primary lip protection
  • Easy to install

$8.16
/EA

HWT-2000X1000 has a wall thickness of 0.5 in. The ID is 1 in and the OD is 2 in. The material is 1026 Carbon Steel.

Heavy Wall Tubes are used for machining high strength and close tolerance parts like bushings, axles, hydraulics, and sleeves.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-4$6.33
5-24$5.53
25-49$4.91
50+$4.43
/IN
at
Select Length
IN
-
IN
  • « PREV
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • NEXT »