Search Results
Filter Your Search
Shop by Category
Designed to fit on one or two piece pistons, this piston seal employs a nitrile seal for high sealability, nylon split back-ups for extrusion resistance, and two split bearing rings. No further support bearings are required.
70A Durometer | NBR Material | 44 MM Nominal Inner Diameter | Piston Seal
Features
- Easy assembly
- Low friction capabilities
Molded in a tough urethane, this seal employs an additional lip near the heel. The twin lip design provides stability, friction-reducing lube retention, and some contaminant resistance. VME – Secondary lip is further from heel than standard MRTU. NOTE: E = European Urethane.
Urethane Material | 36 MM Nominal Inner Diameter | Rod U-Seal
Features
- Excellent low temperature performance
- Easy installation
AN wipers are ideal for light duty and pneumatic applications. Its main purpose is to prevent dirt and contaminants from entering the hydraulic or pneumatic systems. Suffix “SH” designates slotted heel design, “V” designates fluorocarbon material, and “B” designates carboxilated nitrile material.
90A Durometer | Urethane Material | 1 in Nominal Inner Diameter
Features
- Flexible, snap-in design for easy installation into closed housings
- Low compression set
HT-7750X7000 has a wall thickness of 0.375 in. The ID is 7 in and the OD is 7.75 in. The material is DOM 1026 Steel – ST52.3 and has been stress-relieved and annealed.
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
1-14 | $15.02 |
15-59 | $13.13 |
60-89 | $11.66 |
90+ | $10.50 |
Hytrel backup ring with a flat cross-section.
Molded of 55D Durometer Hytrel, these back-up rings provide excellent extrusion resistance and tolerance to fluids such as phosphate esters, hydraulic oil and water. Stretched for installation, they return quickly to their original size for easy installation.
55D Durometer | Hytrel Material | 4 1/4 in Nominal Inner Diameter | 0.11 in Cross Section | Backup Ring
Features
- Improved extrusion resistance compared to standard FKM or NBR backups
- Can be stretched over larger diameters and will return quickly to their original size
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.
70 Durometer | Buna-N Rubber Material | 1 5/8 in Nominal Inner Diameter | 1/16 in Cross Section | O-Ring
Features
- Pressure range varies according to diametral clearance
- Temperature range of -40 °F to -240 °F
Hytrel backup ring with a flat cross-section.
Molded of 55D Durometer Hytrel, these back-up rings provide excellent extrusion resistance and tolerance to fluids such as phosphate esters, hydraulic oil and water. Stretched for installation, they return quickly to their original size for easy installation.
55D Durometer | Hytrel Material | 3 3/4 in Nominal Inner Diameter | 0.11 in Cross Section | Backup Ring
Features
- Improved extrusion resistance compared to standard FKM or NBR backups
- Can be stretched over larger diameters and will return quickly to their original size
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
ALHT2250X2000 has a 0.125 in wall thickness. The ID is 2 in and the OD is 2.25 in. The material is 6063-T832 Aluminum.
Seamless extruded and cold-drawn. Hard coated on the ID which gives the aluminum tube a tough, abrasive-resitant surface.
6063-T832 Aluminum is used for pneumatic cylinder applications requiring very good corrosion resistance and/or light weight. Can also be used for low-pressure oil cylinders (250 psi or less).
- No machining required on the ID
- Seamless extruded and cold-drawn
- Hard coated interior
- Corrosion resistance
- Good weldability
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
1-14 | $3.93 |
15-29 | $3.15 |
30-104 | $2.25 |
105+ | $1.75 |
HWT-5500X3000 has a wall thickness of 1.25 in. The ID is 3 in and the OD is 5.5 in. The material is 1026 Carbon Steel.
Heavy Wall Tubes are used for machining high strength and close tolerance parts like bushings, axles, hydraulics, and sleeves.
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
1-4 | $16.79 |
5-24 | $14.68 |
25-49 | $13.03 |
50+ | $11.74 |