Search Results

Molded in a tough urethane, this seal employs an additional lip near the heel. The twin lip design provides stability, friction-reducing lube retention, and some contaminant resistance. VME – Secondary lip is further from heel than standard MRTU. NOTE: E = European Urethane.

Urethane Material | 25 MM Nominal Inner Diameter | Rod U-Seal

Features

• Excellent low temperature performance
• Easy installation

Style ST-XL wipers are molded from premium urethane and are direct replacements for Style “ST” or “D” wipers. The outside diameter of the ring has a crush lip providing extra interference in the groove. A bead on the shoulder stops contaminates from entering through the groove. The inside diameter is ribbed to prevent pressure traps between the wiper and rod seal.

94A Durometer | Urethane Material | 1 1/4 in Nominal Inner Diameter

Features

• Crush lip to provide extra interference
• Bead on the shoulder to keep contaminants out
• Ribbed ID to prevent pressure traps

US-90URE-2.500×3.000×0.375

.5625 – 18 3000 PSI ORB PORTS #6

Style ST-XL wipers are molded from premium urethane and are direct replacements for Style “ST” or “D” wipers. The outside diameter of the ring has a crush lip providing extra interference in the groove. A bead on the shoulder stops contaminates from entering through the groove. The inside diameter is ribbed to prevent pressure traps between the wiper and rod seal.

94A Durometer | Urethane Material | 3/4 in Nominal Inner Diameter

Features

• Crush lip to provide extra interference
• Bead on the shoulder to keep contaminants out
• Ribbed ID to prevent pressure traps

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70 Durometer | Buna-N Rubber Material | 2 9/16 in Nominal Inner Diameter | 3/32 in Cross Section | O-Ring

Features

• Pressure range varies according to diametral clearance
• Temperature range of -40 °F to -240 °F

HWT-4000X2000 has a wall thickness of 1 in. The ID is 2 in and the OD is 4 in. The material is 1026 Carbon Steel.

Heavy Wall Tubes are used for machining high strength and close tolerance parts like bushings, axles, hydraulics, and sleeves.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

MHT-100X115 has a wall thickness of 7.5 mm. The ID is 100 mm and the OD is 115 mm. The material is 1026 Carbon Steel and has been stress-relieved and annealed.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

MCPO-16 has a 16 mm diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.

ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.

• Extremely smooth surface finish
• Excellent wear and corrosion resistance
• Good strength and impact properties
• Good machinability
• Reasonable weldability
• Fair response to normal heat treating and induction hardening practices

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1.125 in induction hardened chrome shafting.

The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).

Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.

• Greater strength
• Better resistance to mechanical damage

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.