Browse Categories

Search Results

Filter Your Search

Show Attribute Category Group

Shop by Category

Loading...

ALHT5250X5000 has a 0.125 in wall thickness. The ID is 5 in and the OD is 5.25 in. The material is 6063-T832 Aluminum.

Seamless extruded and cold-drawn. Hard coated on the ID which gives the aluminum tube a tough, abrasive-resitant surface.

6063-T832 Aluminum is used for pneumatic cylinder applications requiring very good corrosion resistance and/or light weight. Can also be used for low-pressure oil cylinders (250 psi or less).

  • No machining required on the ID
  • Seamless extruded and cold-drawn
  • Hard coated interior
  • Corrosion resistance
  • Good weldability

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$10.05
15-29$8.36
30-104$7.18
105+$5.58
/IN
at
Select Length
IN
-
IN
3 1/8 X 3 3/8 X 1/8 O-ring NBR70 - 568-235 | CRC Distribution Inc.

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70 Durometer | Buna-N Rubber Material | 3 1/8 in Nominal Inner Diameter | 1/8 in Cross Section | O-Ring

Features

  • Pressure range varies according to diametral clearance
  • Temperature range of -40 °F to -240 °F

$0.77
/EA

Parback® backup ring with a curved cross-section.

Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.

90A Durometer | Buna-N Rubber Material | 2 1/4 in Nominal Inner Diameter | 1/8 in Cross Section | Backup Ring

Features

  • Excellent extrusion resistance
  • Easily stretched for installation
  • Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces

$1.13
/EA

MHT-40X50 has a wall thickness of 5 mm. The ID is 40 mm and the OD is 50 mm. The material is 1026 Carbon Steel and has been stress-relieved and annealed.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$4.29
15-74$3.33
75-104$3.00
105+$2.73
/IN
at
Select Length
IN
-
IN

60mm induction hardened chrome shafting.

The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).

Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.

  • Greater strength
  • Better resistance to mechanical damage

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-29$9.92
30-74$7.09
75-134$5.51
135-287$4.96
288+$4.51
/IN
at
Select Length
IN
-
IN

Designed to fit on one or two piece pistons, this piston seal employs a nitrile seal for high sealability, nylon split back-ups for extrusion resistance, and two split bearing rings. No further support bearings are required.

70A Durometer | NBR Material | 34 MM Nominal Inner Diameter | Piston Seal

Features

  • Easy assembly
  • Low friction capabilities

$21.44
/EA

This light duty wiper is molded in polyurethane and features a double-stepped shoulder to fit tightly in the gland throat.

Urethane Material | 25 MM Inner Diameter | Wiper

Features

  • Double-stepped shoulder

$2.36
/EA
0.625 in Cylinder Tie Rod | CRC Distribution Inc.

TR-625 has a 0.625 in diameter. The material is 1144 Carbon Steel, which is equivalent to Stressproof tie rod.

Tie rods are sold in 12 ft. lengths only. Rods can be cut for UPS shipment or left whole, if necessary. Freight charges may vary depending on required length.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

$56.00
/EA

35mm induction hardened chrome shafting.

The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).

Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.

  • Greater strength
  • Better resistance to mechanical damage

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$5.46
15-29$3.64
30-89$2.73
90-134$2.42
135+$2.18
/IN
at
Select Length
IN
-
IN
2 in Hot Finished 1018 Carbon Steel Round Bar | CRC Distribution Inc.

*
2 in Hot Finished 1018 Carbon Steel*
round bar. Material can be cut to any size.

Suitable for shafting and applications that do not require the greater strength of high carbon and alloy steels.

  • Good case hardening properties
  • Fair machinability
  • Readily brazed and welded

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-4$5.04
5-9$4.03
10-14$2.88
15+$2.52
/IN
at
Select Length
IN
-
IN
  • « PREV
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • NEXT »