Browse Categories

Search Results

Filter Your Search

Show Attribute Category Group

Shop by Category

Loading...

MHT-63X77 has a wall thickness of 7 mm. The ID is 63 mm and the OD is 77 mm. The material is 1026 Carbon Steel and has been stress-relieved and annealed.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$9.81
15-74$7.61
75-104$6.86
105+$6.24
/IN
at
Select Length
IN
-
IN

32mm induction hardened chrome shafting.

The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).

Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.

  • Greater strength
  • Better resistance to mechanical damage

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$4.11
15-29$2.74
30-89$2.06
90-134$1.83
135+$1.65
/IN
at
Select Length
IN
-
IN

Molded in urethane, this wiper is flexible enough to easily snap into a groove yet tough enough to handle difficult rod wiping applications.

Urethane Material | 30 MM Inner Diameter | Wiper

$5.69
/EA
US-80NBR-1-3/4x2-1/8x3/16 - HRU18-1.75-18 | CRC Distribution Inc.

Style HRU u-seals are precision molded from 80 Durometer Buna-N rubber. Sizes include those found in Army-Navy spec. AN6226 and narrow cross-section sizes found in J.I.C. cylinders and the popularly termed “Huva Cup”.

80A Durometer | Buna-N Rubber Material | 1 3/4 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal

$3.67
/EA

Featuring high pressure and high shock load capability, this seal utilizes the same twin lip design found in Hercules®, Sealing Products’ RTU style. With the main body of the seal molded from high performance polyurethane, this seal, incorporates a dynamically designed nitrile energizer and a tough polyacetal anti-extrusion ring. RTUB is capable of, pressures up to 10,000 psi in approved applications. Please consult Hercules Engineering for pressures above 6,000, psi.

The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland. The unique profile of the NBR energizer ensures the primary sealing lips maintain contact under low or no pressure situations while ensuring proper sealing at higher pressures. The Hallite 621 also incorporates an acetyl anti-extrusion ring to withstand side loads and extreme pressure peaks even with the extrusion gaps.

94A Durometer | Urethane Material | 2 in Nominal Inner Diameter | 1/4 in Cross Section | U-Seal

$26.87
/EA

0.75 in induction hardened chrome shafting.

The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).

Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.

  • Greater strength
  • Better resistance to mechanical damage

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-29$3.20
30-59$1.92
60-89$1.60
90-134$1.07
135+$0.96
/IN
at
Select Length
IN
-
IN

HT-3750X3250 has a wall thickness of 0.25 in. The ID is 3.25 in and the OD is 3.75 in. The material is DOM 1026 Steel – ST52.3 and has been stress-relieved and annealed.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$5.58
15-59$4.80
60-104$4.19
105-149$3.72
150+$3.35
/IN
at
Select Length
IN
-
IN

Parback® backup ring with a curved cross-section.

Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.

90A Durometer | Buna-N Rubber Material | 3 3/4 in Nominal Inner Diameter | 1/8 in Cross Section | Backup Ring

Features

  • Excellent extrusion resistance
  • Easily stretched for installation
  • Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces

$2.08
/EA

CPO-0875 has a 0.875 in diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.

ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.

  • Extremely smooth surface finish
  • Excellent wear and corrosion resistance
  • Good strength and impact properties
  • Good machinability
  • Reasonable weldability
  • Fair response to normal heat treating and induction hardening practices

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-29$3.40
30-74$1.46
75-119$1.28
120+$1.13
/IN
at
Select Length
IN
-
IN

ALHT6250X6000 has a 0.125 in wall thickness. The ID is 6 in and the OD is 6.25 in. The material is 6063-T832 Aluminum.

Seamless extruded and cold-drawn. Hard coated on the ID which gives the aluminum tube a tough, abrasive-resitant surface.

6063-T832 Aluminum is used for pneumatic cylinder applications requiring very good corrosion resistance and/or light weight. Can also be used for low-pressure oil cylinders (250 psi or less).

  • No machining required on the ID
  • Seamless extruded and cold-drawn
  • Hard coated interior
  • Corrosion resistance
  • Good weldability

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$15.00
15-29$12.49
30-104$10.73
105+$8.33
/IN
at
Select Length
IN
-
IN
  • « PREV
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • NEXT »