Search Results
Filter Your Search
Category Group
Shop by Category
MCPO-65 has a 65 mm diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.
ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.
- Extremely smooth surface finish
- Excellent wear and corrosion resistance
- Good strength and impact properties
- Good machinability
- Reasonable weldability
- Fair response to normal heat treating and induction hardening practices
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-29 | $11.68 |
| 30-74 | $8.35 |
| 75-134 | $6.48 |
| 135-287 | $5.84 |
| 288+ | $5.31 |
56mm induction hardened chrome shafting.
The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).
Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.
- Greater strength
- Better resistance to mechanical damage
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-29 | $9.07 |
| 30-74 | $6.49 |
| 75-134 | $5.04 |
| 135-287 | $4.54 |
| 288+ | $4.13 |
90mm induction hardened chrome shafting.
The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).
Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.
- Greater strength
- Better resistance to mechanical damage
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-29 | $21.28 |
| 30-59 | $15.22 |
| 60-119 | $11.81 |
| 120-287 | $10.64 |
| 288+ | $9.68 |
Parback® backup ring with a curved cross-section.
Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.
90A Durometer | Buna-N Rubber Material | 3 5/8 in Nominal Inner Diameter | 3/16 in Cross Section | Backup Ring
Features
- Excellent extrusion resistance
- Easily stretched for installation
- Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces
Utilizing a sturdy metal case, these wipers are molded from the same high performance urethane used in our Heavy Duty U-seals. Built for severe service, these wipers are capable of surviving hostile environments.
92A Durometer | Urethane Material | 1 1/2 in Nominal Inner Diameter
Features
- Used in Heavy Duty U-seals
- Capable of surviving hostile environments
- Molded from the high performance urethane
HT-2875X2500 has a wall thickness of 0.1875 in. The ID is 2.5 in and the OD is 2.875 in. The material is DOM 1026 Steel – ST52.3 and has been stress-relieved and annealed.
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-14 | $3.60 |
| 15-59 | $3.09 |
| 60-104 | $2.70 |
| 105-149 | $2.40 |
| 150+ | $2.16 |
AN wipers are ideal for light duty and pneumatic applications. Its main purpose is to prevent dirt and contaminants from entering the hydraulic or pneumatic systems. Suffix “SH” designates slotted heel design, “V” designates fluorocarbon material, and “B” designates carboxilated nitrile material.
90A Durometer | Urethane Material | 2 in Nominal Inner Diameter
Features
- Flexible, snap-in design for easy installation into closed housings
- Low compression set
ALHT4250X4000 has a 0.125 in wall thickness. The ID is 4 in and the OD is 4.25 in. The material is 6063-T832 Aluminum.
Seamless extruded and cold-drawn. Hard coated on the ID which gives the aluminum tube a tough, abrasive-resitant surface.
6063-T832 Aluminum is used for pneumatic cylinder applications requiring very good corrosion resistance and/or light weight. Can also be used for low-pressure oil cylinders (250 psi or less).
- No machining required on the ID
- Seamless extruded and cold-drawn
- Hard coated interior
- Corrosion resistance
- Good weldability
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-14 | $8.11 |
| 15-29 | $6.75 |
| 30-104 | $5.80 |
| 105+ | $4.50 |
ALHT6250X6000 has a 0.125 in wall thickness. The ID is 6 in and the OD is 6.25 in. The material is 6063-T832 Aluminum.
Seamless extruded and cold-drawn. Hard coated on the ID which gives the aluminum tube a tough, abrasive-resitant surface.
6063-T832 Aluminum is used for pneumatic cylinder applications requiring very good corrosion resistance and/or light weight. Can also be used for low-pressure oil cylinders (250 psi or less).
- No machining required on the ID
- Seamless extruded and cold-drawn
- Hard coated interior
- Corrosion resistance
- Good weldability
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-14 | $15.00 |
| 15-29 | $12.49 |
| 30-104 | $10.73 |
| 105+ | $8.33 |
HT-2500X2000 has a wall thickness of 0.25 in. The ID is 2 in and the OD is 2.5 in. The material is DOM 1026 Steel – ST52.3 and has been stress-relieved and annealed.
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-14 | $3.89 |
| 15-59 | $3.34 |
| 60-104 | $2.92 |
| 105-149 | $2.59 |
| 150+ | $2.34 |
