Browse Categories

Search Results

Filter Your Search

Show Attribute Category Group

Shop by Category

Loading...

30mm induction hardened chrome shafting.

The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).

Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.

  • Greater strength
  • Better resistance to mechanical damage

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$3.88
15-29$2.58
30-89$1.94
90-134$1.72
135+$1.55
/IN
at
Select Length
IN
-
IN

Molded from filled PTFE and machined to close tolerances, these seals feature low friction and excellent wear characteristics. Nitrile rings are used for energizers.

70A Durometer | PTFE Material | 39 MM Nominal Inner Diameter | Piston Seal

Features

  • Easy assembly
  • Low friction capabilities

$18.34
/EA
568-124 | 1 1/4 X 1 7/16 X 3/32 O-ring NBR70(50) | CRC Distribution Inc.

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70 Durometer | Buna-N Rubber Material | 1 1/4 in Nominal Inner Diameter | 3/32 in Cross Section | O-Ring

Features

  • Pressure range varies according to diametral clearance
  • Temperature range of -40 °F to -240 °F

$0.22
/EA

CPO-0875 has a 0.875 in diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.

ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.

  • Extremely smooth surface finish
  • Excellent wear and corrosion resistance
  • Good strength and impact properties
  • Good machinability
  • Reasonable weldability
  • Fair response to normal heat treating and induction hardening practices

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-29$3.40
30-74$1.46
75-119$1.28
120+$1.13
/IN
at
Select Length
IN
-
IN

MCPO-100 has a 100 mm diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.

ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.

  • Extremely smooth surface finish
  • Excellent wear and corrosion resistance
  • Good strength and impact properties
  • Good machinability
  • Reasonable weldability
  • Fair response to normal heat treating and induction hardening practices

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$24.84
15-29$17.76
30-59$15.53
60-119$12.42
120+$11.30
/IN
at
Select Length
IN
-
IN

Style ST-XL wipers are molded from premium urethane and are direct replacements for Style “ST” or “D” wipers. The outside diameter of the ring has a crush lip providing extra interference in the groove. A bead on the shoulder stops contaminates from entering through the groove. The inside diameter is ribbed to prevent pressure traps between the wiper and rod seal.

94A Durometer | Urethane Material | 1 1/8 in Nominal Inner Diameter

Features

  • Crush lip to provide extra interference
  • Bead on the shoulder to keep contaminants out
  • Ribbed ID to prevent pressure traps

$4.49
/EA
568-133 | 1 13/16 X 2 X 3/32 O-ring NBR70 | CRC Distribution Inc.

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70 Durometer | Buna-N Rubber Material | 1 13/16 in Nominal Inner Diameter | 3/32 in Cross Section | O-Ring

Features

  • Pressure range varies according to diametral clearance
  • Temperature range of -40 °F to -240 °F

$0.36
/EA

ALHT5250X5000 has a 0.125 in wall thickness. The ID is 5 in and the OD is 5.25 in. The material is 6063-T832 Aluminum.

Seamless extruded and cold-drawn. Hard coated on the ID which gives the aluminum tube a tough, abrasive-resitant surface.

6063-T832 Aluminum is used for pneumatic cylinder applications requiring very good corrosion resistance and/or light weight. Can also be used for low-pressure oil cylinders (250 psi or less).

  • No machining required on the ID
  • Seamless extruded and cold-drawn
  • Hard coated interior
  • Corrosion resistance
  • Good weldability

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$10.05
15-29$8.36
30-104$7.18
105+$5.58
/IN
at
Select Length
IN
-
IN

HT-3750X3250 has a wall thickness of 0.25 in. The ID is 3.25 in and the OD is 3.75 in. The material is DOM 1026 Steel – ST52.3 and has been stress-relieved and annealed.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$5.58
15-59$4.80
60-104$4.19
105-149$3.72
150+$3.35
/IN
at
Select Length
IN
-
IN

MCPO-55 has a 55 mm diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.

ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.

  • Extremely smooth surface finish
  • Excellent wear and corrosion resistance
  • Good strength and impact properties
  • Good machinability
  • Reasonable weldability
  • Fair response to normal heat treating and induction hardening practices

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$11.44
15-29$7.62
30-89$5.72
90-134$5.08
135+$4.58
/IN
at
Select Length
IN
-
IN
  • « PREV
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • NEXT »