Browse Categories

Search Results

Filter Your Search

Show Attribute Category Group

Shop by Category

Loading...
45 X 55 X 7.3 Twin Lip URE - MRTU-45X55X7.3 | CRC Distribution Inc.

Molded in a tough urethane, this seal employs an additional lip near the heel. The twin lip design provides stability, friction-reducing lube retention, and some contaminant resistance. VME – Secondary lip is further from heel than standard MRTU. NOTE: E = European Urethane.

Urethane Material | 45 MM Nominal Inner Diameter | Rod U-Seal

Features

  • Excellent low temperature performance
  • Easy installation

$13.31
/EA

Cast Iron Rod Clevis Mount with a 1.875 in – 12 TPI threaded end and a 2 in pin hole.

Clevis mounts help maintain alignment and protect the cylinder from side load. Mounts attach to threaded stud ends, pivot holes, or bolt holes on the cylinder. Can be used with hydraulic cylinders with standard bore sizes.

$144.00
/PC

HT-6500X6000 has a wall thickness of 0.25 in. The ID is 6 in and the OD is 6.5 in. The material is DOM 1026 Steel – ST52.3 and has been stress-relieved and annealed.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$8.55
15-59$7.47
60-89$6.63
90-119$5.98
120+$5.44
/IN
at
Select Length
IN
-
IN

Parback® backup ring with a curved cross-section.

Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.

90A Durometer | Buna-N Rubber Material | 3 1/8 in Nominal Inner Diameter | 3/16 in Cross Section | Backup Ring

Features

  • Excellent extrusion resistance
  • Easily stretched for installation
  • Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces

$1.87
/EA
3 1/2 X 3 11/16 X 3/32 O-ring NBR70(20) - 568-153 | CRC Distribution Inc.

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70 Durometer | Buna-N Rubber Material | 3 1/2 in Nominal Inner Diameter | 3/32 in Cross Section | O-Ring

Features

  • Pressure range varies according to diametral clearance
  • Temperature range of -40 °F to -240 °F

$0.81
/EA

HT-8000X7000 has a wall thickness of 0.5 in. The ID is 7 in and the OD is 8 in. The material is DOM 1026 Steel – ST52.3 and has been stress-relieved and annealed.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$20.54
15-59$17.95
60-89$15.94
90+$14.36
/IN
at
Select Length
IN
-
IN
1 in 17-4 Stainless Steel - Standard Chrome | CRC Distribution Inc.

SS17-4/CPO-1000 has a 1 in diameter. The material is 17-4 Stainless Steel, H1150 with Standard Chrome on the exterior.

Commonly used in offshore cranes, marine cylinders, and marine steering cylinders.

  • Highest level of corrosion resistance

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$4.65
15-44$3.99
45-89$3.49
90-104$3.10
105+$2.79
/IN
at
Select Length
IN
-
IN
1 X 1 3/16 X 3/32 O-ring NBR70 - 568-120 | CRC Distribution Inc.

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70 Durometer | Buna-N Rubber Material | 1 in Nominal Inner Diameter | 3/32 in Cross Section | O-Ring

Features

  • Pressure range varies according to diametral clearance
  • Temperature range of -40 °F to -240 °F

$0.13
/EA

ALHT5250X5000 has a 0.125 in wall thickness. The ID is 5 in and the OD is 5.25 in. The material is 6063-T832 Aluminum.

Seamless extruded and cold-drawn. Hard coated on the ID which gives the aluminum tube a tough, abrasive-resitant surface.

6063-T832 Aluminum is used for pneumatic cylinder applications requiring very good corrosion resistance and/or light weight. Can also be used for low-pressure oil cylinders (250 psi or less).

  • No machining required on the ID
  • Seamless extruded and cold-drawn
  • Hard coated interior
  • Corrosion resistance
  • Good weldability

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$10.05
15-29$8.36
30-104$7.18
105+$5.58
/IN
at
Select Length
IN
-
IN

MCPO-18 has a 18 mm diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.

ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.

  • Extremely smooth surface finish
  • Excellent wear and corrosion resistance
  • Good strength and impact properties
  • Good machinability
  • Reasonable weldability
  • Fair response to normal heat treating and induction hardening practices

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-29$3.30
30-59$1.65
60-89$1.42
90-134$1.10
135+$0.99
/IN
at
Select Length
IN
-
IN
  • « PREV
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • NEXT »