Search Results
Filter Your Search
Shop by Category
Featuring high pressure and high shock load capability, this seal utilizes the same twin lip design found in Hercules®, Sealing Products’ RTU style. With the main body of the seal molded from high performance polyurethane, this seal, incorporates a dynamically designed nitrile energizer and a tough polyacetal anti-extrusion ring. RTUB is capable of, pressures up to 10,000 psi in approved applications. Please consult Hercules Engineering for pressures above 6,000, psi.
The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland. The unique profile of the NBR energizer ensures the primary sealing lips maintain contact under low or no pressure situations while ensuring proper sealing at higher pressures. The Hallite 621 also incorporates an acetyl anti-extrusion ring to withstand side loads and extreme pressure peaks even with the extrusion gaps.
94A Durometer | Urethane Material | 2 1/2 in Nominal Inner Diameter | 1/4 in Cross Section | U-Seal
The twin lip design helps solve difficult rod sealing problems by providing lower friction, increased stability, and high, dynamic lip force, while preventing air penetration from outside the cylinder.
Asymmetric rod seal designed with precision trimmed sealing lips to provide a dry sealing solution in light and medium-duty applications. The Hallite 605 is molded in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation and excellent low temperature performance.
Designed to have interference in the seal housing groove and has a secondary lip. The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland. The inner dynamic lip is shorter and more robust to improve sealing and compression set characteristics over conventional, symmetrical U-seals. The seal can be considered for use in heavy-duty applications when used with a suitable full depth back-up ring. The sealing lips are precision trimmed at an angle to give optimal rod sealing performance.
94A Durometer | Urethane Material | 1 in Nominal Inner Diameter | 1/8 in Cross Section | U-Seal
Features
- General purpose rod seal
- Robust design
- Excellent wear resistance
- Increase seal stability
- Performs well over wide temperature range and is extremely effective in low temperatures
- Primary lip protection
- Easy to install
The PS1400 seals offer low friction and high strength in a compact double-acting piston seal design. The PTFE seal ring, combined with a rubber energizer, assures positive contact with the dynamic surface. The PS1400 is designed to fit ANSI/B93.32-1973 groove standards. Piston diameter “I” dimensions are given for pistons without wear rings.
15% Glass Filled PTFE Material | 2.108 in Nominal Inner Diameter | Piston Seal
Features
- Easy assembly
- Low friction capabilities
Cast Iron Rod Clevis Mount with a 1.875 in – 12 TPI threaded end and a 2 in pin hole.
Clevis mounts help maintain alignment and protect the cylinder from side load. Mounts attach to threaded stud ends, pivot holes, or bolt holes on the cylinder. Can be used with hydraulic cylinders with standard bore sizes.
25mm induction hardened chrome shafting.
The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).
Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.
- Greater strength
- Better resistance to mechanical damage
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
1-14 | $3.60 |
15-29 | $2.40 |
30-89 | $1.80 |
90-134 | $1.60 |
135+ | $1.44 |
Totally interchangeable with Style PS1400 PTFE piston seals, Style PS1500 piston seals are molded from tough 60 Shore D durometer polyurethane. During the molding process, a .002” thick band of molybdenum disulfide is molded into the outside diameter of the seal ring for reduced friction. PS1500 piston seals are easily stretched over the piston and recover rapidly with the elimination of the “cold flow” characteristics found in PTFE seals. Piston diameter “I” dimensions are given for pistons without wear rings.
60 Shore D Durometer | Polyurethane Material | 2.106 in Nominal Inner Diameter | Piston Seal
Features
- Easy assembly
- Low friction capabilities
0.75 in clevis pin with 0.048 in grooves machined into each end to fit two retaining rings. Retaining rings are not included.
Pivot pins with grooves are meant to be used on a hydraulic cylinder that extends and retracts a telescoping lift arm.
HT-6500X6000 has a wall thickness of 0.25 in. The ID is 6 in and the OD is 6.5 in. The material is DOM 1026 Steel – ST52.3 and has been stress-relieved and annealed.
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
1-14 | $8.55 |
15-59 | $7.47 |
60-89 | $6.63 |
90-119 | $5.98 |
120+ | $5.44 |
MCPO-55 has a 55 mm diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.
ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.
- Extremely smooth surface finish
- Excellent wear and corrosion resistance
- Good strength and impact properties
- Good machinability
- Reasonable weldability
- Fair response to normal heat treating and induction hardening practices
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
1-14 | $11.44 |
15-29 | $7.62 |
30-89 | $5.72 |
90-134 | $5.08 |
135+ | $4.58 |