Browse Categories

Search Results

Filter Your Search

Show Attribute Category Group

Shop by Category

Loading...

GB-PHEN-1×1/8-C/S TURQUOISE

$44.23
/FT

A wide range of ST wipers are now offered in the slotted heel design. The slots in the heel allow excess hydraulic fluid to bypass the wiper, preventing wiper blowout.

90A Durometer | Urethane Material | 1 1/2 in Nominal Inner Diameter

Features

  • Slotted heel design
  • Slots in the heel allow excess hydraulic fluid to bypass the wiper

$4.23
/EA

CPO-1625 has a 1.625 in diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.

ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.

  • Extremely smooth surface finish
  • Excellent wear and corrosion resistance
  • Good strength and impact properties
  • Good machinability
  • Reasonable weldability
  • Fair response to normal heat treating and induction hardening practices

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$7.74
15-29$5.16
30-89$3.69
90-134$2.86
135+$2.58
/IN
at
Select Length
IN
-
IN

UPS – RED RATE

$29.00
/EA

T-Seals combine a resilient sealing ring with a hard, split back-up ring on each side of the sealing element. The assembly installs in a standard o-ring groove. T-Seals are non-spiraling and extrusion resistant to 5,000 psi with improved tolerances. Intermediate and Wide Base T-Seals are designed to fit MIL-5514F o-ring glands only and interchange with 1 o-ring / 1 back-up ring and 1 o-ring / 2 back-up ring grooves, respectively.

Buna-N Rubber Material | 3 3/8 in Nominal Inner Diameter | Piston T-Seal

$16.90
/EA
Urethane Wiper | CRC Distribution Inc.

AN wipers are ideal for light duty and pneumatic applications. Its main purpose is to prevent dirt and contaminants from entering the hydraulic or pneumatic systems. Suffix “SH” designates slotted heel design, “V” designates fluorocarbon material, and “B” designates carboxilated nitrile material.

90A Durometer | Urethane Material | 2 1/2 in Nominal Inner Diameter

Features

  • Flexible, snap-in design for easy installation into closed housings
  • Low compression set

$2.96
/EA

63mm induction hardened chrome shafting.

The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).

Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.

  • Greater strength
  • Better resistance to mechanical damage

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-29$12.64
30-74$9.04
75-134$7.02
135-287$6.32
288+$5.75
/IN
at
Select Length
IN
-
IN

85mm induction hardened chrome shafting.

The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).

Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.

  • Greater strength
  • Better resistance to mechanical damage

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-29$18.92
30-59$13.53
60-119$10.50
120-287$9.46
288+$8.61
/IN
at
Select Length
IN
-
IN
3.000 X 2.608 X 0.129 TFG - PS1400-48 | CRC Distribution Inc.

The PS1400 seals offer low friction and high strength in a compact double-acting piston seal design. The PTFE seal ring, combined with a rubber energizer, assures positive contact with the dynamic surface. The PS1400 is designed to fit ANSI/B93.32-1973 groove standards. Piston diameter “I” dimensions are given for pistons without wear rings.

15% Glass Filled PTFE Material | 2.608 in Nominal Inner Diameter | Piston Seal

Features

  • Easy assembly
  • Low friction capabilities

$5.75
/EA
2 5/16 X 2 1/2 X 3/32 O-ring NBR70 - 568-141 | CRC Distribution Inc.

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70 Durometer | Buna-N Rubber Material | 2 5/16 in Nominal Inner Diameter | 3/32 in Cross Section | O-Ring

Features

  • Pressure range varies according to diametral clearance
  • Temperature range of -40 °F to -240 °F

$0.51
/EA
  • « PREV
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • NEXT »