Search Results
Filter Your Search
Category Group
Shop by Category
DUCT-7000 has a diameter of 7 in. The material is 65-45-12 Ductile Iron.
65-45-12 Ductile Iron is used to machine pistons, glands, caps, manifolds, rams, and valve bodies.
Ductile has higher machining speeds than steel and there is usually no need for deburring machined parts. The graphite flakes in the material act as a self-lubricant. Ductile can be flame or induction hardened as well as deep hardened.
Ductile bars are produced with sufficient stock on the outside diameter to ensure clean-up at the nominal dimension.
- Excellent machinability
- Optimal impact strengths
- Optimal fatigue properties
- Optimal electrical conductivity
- High magnetic permeability
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-9 | $38.90 |
| 10-39 | $34.54 |
| 40+ | $28.32 |
65mm induction hardened chrome shafting.
The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).
Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.
- Greater strength
- Better resistance to mechanical damage
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-29 | $11.10 |
| 30-74 | $7.93 |
| 75-134 | $6.16 |
| 135-287 | $5.55 |
| 288+ | $5.05 |
Molded in a tough urethane, this seal employs an additional lip near the heel. The twin lip design provides stability, friction-reducing lube retention, and some contaminant resistance. VME – Secondary lip is further from heel than standard MRTU. NOTE: E = European Urethane.
Urethane Material | 40 MM Nominal Inner Diameter | Rod U-Seal
Features
- Excellent low temperature performance
- Easy installation
This light duty wiper is molded in polyurethane and features a double-stepped shoulder to fit tightly in the gland throat.
Urethane Material | 35 MM Inner Diameter | Wiper
Features
- Double-stepped shoulder
MHT-65X3000 has a wall thickness of 5.6 mm. The ID is 65 mm and the OD is 76.2 mm. The material is 1026 Carbon Steel and has been stress-relieved and annealed.
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-14 | $8.29 |
| 15-74 | $6.44 |
| 75-104 | $5.80 |
| 105+ | $5.28 |
Hytrel backup ring with a flat cross-section.
Molded of 55D Durometer Hytrel, these back-up rings provide excellent extrusion resistance and tolerance to fluids such as phosphate esters, hydraulic oil and water. Stretched for installation, they return quickly to their original size for easy installation.
55D Durometer | Hytrel Material | 1 3/4 in Nominal Inner Diameter | 0.11 in Cross Section | Backup Ring
Features
- Improved extrusion resistance compared to standard FKM or NBR backups
- Can be stretched over larger diameters and will return quickly to their original size
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
Molded in urethane, this wiper is flexible enough to easily snap into a groove yet tough enough to handle difficult rod wiping applications.
Urethane Material | 32 MM Inner Diameter | Wiper
Hytrel backup ring with a flat cross-section.
Molded of 55D Durometer Hytrel, these back-up rings provide excellent extrusion resistance and tolerance to fluids such as phosphate esters, hydraulic oil and water. Stretched for installation, they return quickly to their original size for easy installation.
55D Durometer | Hytrel Material | 2 13/16 in Nominal Inner Diameter | 3/32 in Cross Section | Backup Ring
Features
- Improved extrusion resistance compared to standard FKM or NBR backups
- Can be stretched over larger diameters and will return quickly to their original size
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.
90 Durometer | Buna-N Rubber Material | 7 3/4 in Nominal Inner Diameter | 1/8 in Cross Section | O-Ring
Features
- Pressure range varies according to diametral clearance
- Temperature range of -40 °F to -240 °F
