Search Results
Filter Your Search
Category Group
Shop by Category
Utilizing a sturdy metal case, these wipers are molded from the same high performance urethane used in our Heavy Duty U-seals. Built for severe service, these wipers are capable of surviving hostile environments.
92A Durometer | Urethane Material | 1 1/4 in Nominal Inner Diameter
Features
- Used in Heavy Duty U-seals
- Capable of surviving hostile environments
- Molded from the high performance urethane
The twin lip design helps solve difficult rod sealing problems by providing lower friction, increased stability, and high, dynamic lip force, while preventing air penetration from outside the cylinder.
Asymmetric rod seal designed with precision trimmed sealing lips to provide a dry sealing solution in light and medium-duty applications. The Hallite 605 is molded in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation and excellent low temperature performance.
Designed to have interference in the seal housing groove and has a secondary lip. The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland. The inner dynamic lip is shorter and more robust to improve sealing and compression set characteristics over conventional, symmetrical U-seals. The seal can be considered for use in heavy-duty applications when used with a suitable full depth back-up ring. The sealing lips are precision trimmed at an angle to give optimal rod sealing performance.
94A Durometer | Urethane Material | 1 in Nominal Inner Diameter | 1/8 in Cross Section | U-Seal
Features
- General purpose rod seal
- Robust design
- Excellent wear resistance
- Increase seal stability
- Performs well over wide temperature range and is extremely effective in low temperatures
- Primary lip protection
- Easy to install
Parback® backup ring with a curved cross-section.
Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.
90A Durometer | Buna-N Rubber Material | 1 3/8 in Nominal Inner Diameter | 1/8 in Cross Section | Backup Ring
Features
- Excellent extrusion resistance
- Easily stretched for installation
- Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces
Style 590 Back-up Rings feature exceptional strength and abrasion resistance along with a 53 Shore D hardness rating which makes them suitable for high pressure service where extrusion is a problem. Primarily used as a u-seal back-up, these rings can be used with o-rings. They also retrofit urethane and PTFE back-up rings, with greater performance characteristics. “S” suffix designates a split ring.
53 Shore D Durometer | Hytrel Material | 1 3/16 in Nominal Inner Diameter | 5/32 in Cross Section | Backup Ring
Features
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
660-3000X3500 has a 0.25 in thick wall. The ID is 3 in and the OD is 3.5 in. The material is 660 Bronze Copper Alloy 932.
- Long life span
- Machinability rating of 70
- Not subject to dezincification
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-4 | $19.15 |
| 5-9 | $17.01 |
| 10-14 | $15.32 |
| 15+ | $13.94 |
Machined from 1018 Carbon Steel for a 4 in cylinder.
The length is 0.5 in and the lip is 0.25 in in tall.
Base plates are welded to the end of the cylinder opposite the rod end to secure the cylinder. They provide a solid support for the entire cylinder base area.
Machined from 1018 Carbon Steel for a 5 in cylinder.
The length is 1 in and the lip is 0.375 in in tall.
Base plates are welded to the end of the cylinder opposite the rod end to secure the cylinder. They provide a solid support for the entire cylinder base area.
AN wipers are ideal for light duty and pneumatic applications. Its main purpose is to prevent dirt and contaminants from entering the hydraulic or pneumatic systems. Suffix “SH” designates slotted heel design, “V” designates fluorocarbon material, and “B” designates carboxilated nitrile material.
90A Durometer | Urethane Material | 2 3/8 in Nominal Inner Diameter
Features
- Flexible, snap-in design for easy installation into closed housings
- Low compression set
