Browse Categories

Search Results

Filter Your Search

Show Attribute Category Group

Shop by Category

Loading...

Molded in a tough urethane, this seal employs an additional lip near the heel. The twin lip design provides stability, friction-reducing lube retention, and some contaminant resistance. VME – Secondary lip is further from heel than standard MRTU. NOTE: E = European Urethane.

Urethane Material | 50 MM Nominal Inner Diameter | Rod U-Seal

Features

  • Excellent low temperature performance
  • Easy installation

$13.81
/EA

Style 850 u-seals offer excellent resistance to extrusion and abrasion. The round cross-section expander offers energized sealing from zero to 5,000 psi.

95A Durometer | Urethane Material | 1 1/4 in Nominal Inner Diameter | 1/8 in Cross Section | U-Seal

$5.56
/EA

Top-of-the-range twin lip rod seal designed to provide a dry sealing solution in heavy-duty applications. The seal’s shell is molded in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation and excellent low temperature performance. Featuring high pressure and high shock load capability, this seal utilizes the same twin lip design found in Hercules®, Sealing Products’ RTU style. With the main body of the seal molded from high performance polyurethane, this seal, incorporates a dynamically designed nitrile energizer and a tough polyacetal anti-extrusion ring. RTUB is capable of, pressures up to 10,000 psi in approved applications.

94A Durometer | Urethane Material | 4 in Nominal Inner Diameter | 1/4 in Cross Section | U-Seal

Features

  • General purpose rod seal
  • Robust design
  • Excellent wear resistance
  • Increase seal stability
  • Performs well over wide temperature range and is extremely effective in low temperatures
  • Primary lip protection
  • Easy to install

$51.13
/EA

CPO-3750 has a 3.75 in diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.

ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.

  • Extremely smooth surface finish
  • Excellent wear and corrosion resistance
  • Good strength and impact properties
  • Good machinability
  • Reasonable weldability
  • Fair response to normal heat treating and induction hardening practices

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$16.10
15-29$14.07
30-89$11.26
90+$10.25
/IN
at
Select Length
IN
-
IN

CPOD2000X1500 has a wall thickness of 0.25 in. The ID is 1.5 in and the OD is 2 in. The material is 1026 Carbon Steel with chrome plating on the Outside Surface.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$5.39
15-29$4.49
30-59$3.37
60-104$2.99
105+$2.69
/IN
at
Select Length
IN
-
IN

2 in clevis pin with 0.068 in grooves machined into each end to fit two retaining rings. Retaining rings are not included.

Pivot pins with grooves are meant to be used on a hydraulic cylinder that extends and retracts a telescoping lift arm.

$59.01
/PC

Specifically designed as piston seals, these u-seals are engineered to seal on their outside diameter. They offer extended, service life and maximum reliability in piston sealing.

92A Durometer | Urethane Material | 3 in Nominal Inner Diameter | 1/4 in Cross Section | U-Seal

$20.30
/EA

WR, 6 X 3/4 Wear Ring NYL

$12.86
/EA

CIHT3490X3250 has a wall thickness of 0.12 in. The ID is 3.25 in and the OD is 3.49 in. The material is 1026 Carbon Steel with chrome plating on the Inside Surface.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$6.73
15-29$4.81
30-74$3.73
75+$3.36
/IN
at
Select Length
IN
-
IN
Urethane Wiper | CRC Distribution Inc.

AN wipers are ideal for light duty and pneumatic applications. Its main purpose is to prevent dirt and contaminants from entering the hydraulic or pneumatic systems. Suffix “SH” designates slotted heel design, “V” designates fluorocarbon material, and “B” designates carboxilated nitrile material.

90A Durometer | Urethane Material | 4 1/2 in Nominal Inner Diameter

Features

  • Flexible, snap-in design for easy installation into closed housings
  • Low compression set

$5.91
/EA
  • « PREV
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • NEXT »