Browse Categories

Search Results

Filter Your Search

Show Attribute Category Group

Shop by Category

Loading...
5 1/4 X 5 7/16 X 3/32 O-ring NBR70 - 568-160 | CRC Distribution Inc.

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70 Durometer | Buna-N Rubber Material | 5 1/4 in Nominal Inner Diameter | 3/32 in Cross Section | O-Ring

Features

  • Pressure range varies according to diametral clearance
  • Temperature range of -40 °F to -240 °F

$1.50
/EA

DE-07 is a standard rod eye machined from Cast Iron.

A rod eye is a type of mount attached to the end of the cylinder rod. This connects to a mounting point on the machine and usually incorporates a bearing to allow for some movement.

$16.46
/PC

0.75 in clevis pin with two 0.14 in holes that can be used to retain the pin with cotter pins or locking pins. Cotter pins not included.

$4.69
/PC

3.25 in induction hardened chrome shafting.

The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).

Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.

  • Greater strength
  • Better resistance to mechanical damage

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-29$21.62
30-59$15.46
60-119$12.00
120-287$10.81
288+$9.84
/IN
at
Select Length
IN
-
IN
OR-70NBR-110x3-C/S(5) - MOR-110X3 | CRC Distribution Inc.

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70A Durometer | Nitrile Material | 110 MM Nominal Inner Diameter | 3 MM Cross Section | O-Ring

Features

  • Chemical resistance
  • Temperature range of -40 °F to 220 °F

$2.13
/EA
OR-70NBR-79x3-C/S(10) - MOR-79X3 | CRC Distribution Inc.

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70A Durometer | Nitrile Material | 79 MM Nominal Inner Diameter | 3 MM Cross Section | O-Ring

Features

  • Chemical resistance
  • Temperature range of -40 °F to 220 °F

$1.65
/EA

Molded in a tough urethane, this seal employs an additional lip near the heel. The twin lip design provides stability, friction-reducing lube retention, and some contaminant resistance. VME – Secondary lip is further from heel than standard MRTU. NOTE: E = European Urethane.

Urethane Material | 22 MM Nominal Inner Diameter | Rod U-Seal

Features

  • Excellent low temperature performance
  • Easy installation

$11.22
/EA

.4375 – 20 3000 PSI ORB PORTS #4

$2.65
/PC

Asymmetric rod seal designed with precision trimmed sealing lips to provide a dry sealing solution in light and medium-duty applications. The Hallite 605 is molded in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation and excellent low temperature performance. The twin lip design helps solve difficult rod sealing problems by providing lower friction, increased stability, and high, dynamic lip force, while preventing air penetration from outside the cylinder. Designed to have interference in the seal housing groove and has a secondary lip. The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland. The inner dynamic lip is shorter and more robust to improve sealing and compression set characteristics over conventional, symmetrical U-seals.

The seal can be considered for use in heavy-duty applications when used with a suitable full depth back-up ring. The sealing lips are precision trimmed at an angle to give optimal rod sealing performance.

94A Durometer | Urethane Material | 2 3/4 in Nominal Inner Diameter | 1/4 in Cross Section | U-Seal

Features

  • General purpose rod seal
  • Robust design
  • Excellent wear resistance
  • Increase seal stability
  • Performs well over wide temperature range and is extremely effective in low temperatures
  • Primary lip protection
  • Easy to install

$19.78
/EA
OR-70NBR-55x2.5-C/S(20) - MOR-55X2.5 | CRC Distribution Inc.

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70A Durometer | Nitrile Material | 55 MM Nominal Inner Diameter | 2.5 MM Cross Section | O-Ring

Features

  • Chemical resistance
  • Temperature range of -40 °F to 220 °F

$0.92
/EA
  • « PREV
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • NEXT »