Search Results
Filter Your Search
Shop by Category
TSS, 2 1/2 X 1/2 Wear Ring CT
DUCT-4500 has a diameter of 4.5 in. The material is 65-45-12 Ductile Iron.
65-45-12 Ductile Iron is used to machine pistons, glands, caps, manifolds, rams, and valve bodies.
Ductile has higher machining speeds than steel and there is usually no need for deburring machined parts. The graphite flakes in the material act as a self-lubricant. Ductile can be flame or induction hardened as well as deep hardened.
Ductile bars are produced with sufficient stock on the outside diameter to ensure clean-up at the nominal dimension.
- Excellent machinability
- Optimal impact strengths
- Optimal fatigue properties
- Optimal electrical conductivity
- High magnetic permeability
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
1-9 | $18.58 |
10-39 | $14.42 |
40+ | $11.82 |
Asymmetric rod seal designed with precision trimmed sealing lips to provide a dry sealing solution in light and medium-duty applications. The Hallite 605 is molded in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation and excellent low temperature performance. The twin lip design helps solve difficult rod sealing problems by providing lower friction, increased stability, and high, dynamic lip force, while preventing air penetration from outside the cylinder. Designed to have interference in the seal housing groove and has a secondary lip. The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland. The inner dynamic lip is shorter and more robust to improve sealing and compression set characteristics over conventional, symmetrical U-seals.
The seal can be considered for use in heavy-duty applications when used with a suitable full depth back-up ring. The sealing lips are precision trimmed at an angle to give optimal rod sealing performance.
94A Durometer | Urethane Material | 1 1/2 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal
Features
- General purpose rod seal
- Robust design
- Excellent wear resistance
- Increase seal stability
- Performs well over wide temperature range and is extremely effective in low temperatures
- Primary lip protection
- Easy to install
Parback® backup ring with a curved cross-section.
Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.
90A Durometer | Buna-N Rubber Material | 2 1/2 in Nominal Inner Diameter | 1/8 in Cross Section | Backup Ring
Features
- Excellent extrusion resistance
- Easily stretched for installation
- Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces
Style HRU u-seals are precision molded from 80 Durometer Buna-N rubber. Sizes include those found in Army-Navy spec. AN6226 and narrow cross-section sizes found in J.I.C. cylinders and the popularly termed “Huva Cup”.
80A Durometer | Buna-N Rubber Material | 3 1/2 in Nominal Inner Diameter | 1/4 in Cross Section | U-Seal
Cast Iron Rod Clevis Mount with a 1.25 in – 12 TPI threaded end and a 1.75 in pin hole.
Clevis mounts help maintain alignment and protect the cylinder from side load. Mounts attach to threaded stud ends, pivot holes, or bolt holes on the cylinder. Can be used with hydraulic cylinders with standard bore sizes.
O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.
70 Durometer | Buna-N Rubber Material | 2 1/4 in Nominal Inner Diameter | 1/16 in Cross Section | O-Ring
Features
- Pressure range varies according to diametral clearance
- Temperature range of -40 °F to -240 °F
AN wipers are ideal for light duty and pneumatic applications. Its main purpose is to prevent dirt and contaminants from entering the hydraulic or pneumatic systems. Suffix “SH” designates slotted heel design, “V” designates fluorocarbon material, and “B” designates carboxilated nitrile material.
90A Durometer | Urethane Material | 2 3/8 in Nominal Inner Diameter
Features
- Flexible, snap-in design for easy installation into closed housings
- Low compression set
CPOD1000X500 has a wall thickness of 0.25 in. The ID is 0.5 in and the OD is 1 in. The material is 1026 Carbon Steel with chrome plating on the Outside Surface.
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
1-14 | $5.35 |
15-29 | $4.46 |
30-59 | $3.35 |
60-104 | $2.97 |
105+ | $2.68 |