Browse Categories

Search Results

Filter Your Search

Show Attribute Category Group

Shop by Category

Loading...

Style 850 u-seals offer excellent resistance to extrusion and abrasion. The round cross-section expander offers energized sealing from zero to 5,000 psi.

95A Durometer | Urethane Material | 1 3/8 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal

$7.53
/EA
US-80NBR-3-1/2x4x1/4 - HRU25-3.50-25 | CRC Distribution Inc.

Style HRU u-seals are precision molded from 80 Durometer Buna-N rubber. Sizes include those found in Army-Navy spec. AN6226 and narrow cross-section sizes found in J.I.C. cylinders and the popularly termed “Huva Cup”.

80A Durometer | Buna-N Rubber Material | 3 1/2 in Nominal Inner Diameter | 1/4 in Cross Section | U-Seal

$6.90
/EA

Parback® backup ring with a curved cross-section.

Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.

90A Durometer | Buna-N Rubber Material | 5 1/2 in Nominal Inner Diameter | 1/4 in Cross Section | Backup Ring

Features

  • Excellent extrusion resistance
  • Easily stretched for installation
  • Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces

$5.57
/EA

CIHT5235X5000 has a wall thickness of 0.1175 in. The ID is 5 in and the OD is 5.235 in. The material is 1026 Carbon Steel with chrome plating on the Inside Surface.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$9.70
15-29$6.93
30-74$5.38
75+$4.85
/IN
at
Select Length
IN
-
IN
SOR-75NBR-5.25x1/4-C/S(3) - 580-431 | CRC Distribution Inc.

Style 580 Square O-rings are circular elastomeric rings that create a seal between two or more parts. They are made from a variety of materials, including BUNA-N rubber, and are used in a variety of industries, including automotive, aerospace, and manufacturing.

Buna-N Rubber Material | 5 1/4 in Nominal Inner Diameter | 1/4 in Cross Section | Square O-ring

Features

  • Pressure range varies according to diametral clearance
  • Temperature range of -40 °F to -240 °F

$4.78
/EA

2 Bronze Rod Glands

$99.73
/EA

Style ST-XL wipers are molded from premium urethane and are direct replacements for Style “ST” or “D” wipers. The outside diameter of the ring has a crush lip providing extra interference in the groove. A bead on the shoulder stops contaminates from entering through the groove. The inside diameter is ribbed to prevent pressure traps between the wiper and rod seal.

94A Durometer | Urethane Material | 1 1/8 in Nominal Inner Diameter

Features

  • Crush lip to provide extra interference
  • Bead on the shoulder to keep contaminants out
  • Ribbed ID to prevent pressure traps

$4.49
/EA

Asymmetric rod seal designed with precision trimmed sealing lips to provide a dry sealing solution in light and medium-duty applications. The Hallite 605 is molded in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation and excellent low temperature performance. The twin lip design helps solve difficult rod sealing problems by providing lower friction, increased stability, and high, dynamic lip force, while preventing air penetration from outside the cylinder. Designed to have interference in the seal housing groove and has a secondary lip. The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland. The inner dynamic lip is shorter and more robust to improve sealing and compression set characteristics over conventional, symmetrical U-seals.

The seal can be considered for use in heavy-duty applications when used with a suitable full depth back-up ring. The sealing lips are precision trimmed at an angle to give optimal rod sealing performance.

94A Durometer | Urethane Material | 1 1/2 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal

Features

  • General purpose rod seal
  • Robust design
  • Excellent wear resistance
  • Increase seal stability
  • Performs well over wide temperature range and is extremely effective in low temperatures
  • Primary lip protection
  • Easy to install

$10.63
/EA

DUCT-6000 has a diameter of 6 in. The material is 65-45-12 Ductile Iron.

65-45-12 Ductile Iron is used to machine pistons, glands, caps, manifolds, rams, and valve bodies.

Ductile has higher machining speeds than steel and there is usually no need for deburring machined parts. The graphite flakes in the material act as a self-lubricant. Ductile can be flame or induction hardened as well as deep hardened.

Ductile bars are produced with sufficient stock on the outside diameter to ensure clean-up at the nominal dimension.

  • Excellent machinability
  • Optimal impact strengths
  • Optimal fatigue properties
  • Optimal electrical conductivity
  • High magnetic permeability

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-9$28.60
10-39$25.40
40+$20.82
/IN
at
Select Length
IN
-
IN

Molded from filled PTFE and machined to close tolerances, these seals feature low friction and excellent wear characteristics. Nitrile rings are used for energizers.

70A Durometer | PTFE Material | 39 MM Nominal Inner Diameter | Piston Seal

Features

  • Easy assembly
  • Low friction capabilities

$18.34
/EA
  • « PREV
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • NEXT »