Browse Categories

Search Results

Filter Your Search

Show Attribute Category Group

Shop by Category

Loading...

JD-50MM-IT

$5.25
/EA

Rubber Material | 1 1/16 in Nominal Inner Diameter | Wiper

Rubber Material | 1 1/16 in Nominal Inner Diameter | Wiper

$4.53
/EA

MCPO-12 has a 12 mm diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.

ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.

  • Extremely smooth surface finish
  • Excellent wear and corrosion resistance
  • Good strength and impact properties
  • Good machinability
  • Reasonable weldability
  • Fair response to normal heat treating and induction hardening practices

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-29$2.17
30-59$1.08
60-89$0.93
90-134$0.72
135+$0.65
/IN
at
Select Length
IN
-
IN

Molded in a tough urethane, this rod u-seal fits tightly in the groove while providing increased radial force on the rod.

Urethane Material | 36 MM Nominal Inner Diameter | Rod U-Seal

$12.85
/EA

Molded in a tough urethane, this seal employs an additional lip near the heel. The twin lip design provides stability, friction-reducing lube retention, and some contaminant resistance. VME – Secondary lip is further from heel than standard MRTU. NOTE: E = European Urethane.

Urethane Material | 35 MM Nominal Inner Diameter | Rod U-Seal

Features

  • Excellent low temperature performance
  • Easy installation

$13.61
/EA

Hytrel backup ring with a flat cross-section.

Molded of 55D Durometer Hytrel, these back-up rings provide excellent extrusion resistance and tolerance to fluids such as phosphate esters, hydraulic oil and water. Stretched for installation, they return quickly to their original size for easy installation.

55D Durometer | Hytrel Material | 1 1/2 in Nominal Inner Diameter | 0.11 in Cross Section | Backup Ring

Features

  • Improved extrusion resistance compared to standard FKM or NBR backups
  • Can be stretched over larger diameters and will return quickly to their original size
  • High strength and abrasion resistance
  • Wide temperature range
  • Chemical resistance
  • Low friction
  • Easy installation

$1.13
/EA

ALHT4750X4500 has a 0.125 in wall thickness. The ID is 4.5 in and the OD is 4.75 in. The material is 6063-T832 Aluminum.

Seamless extruded and cold-drawn. Hard coated on the ID which gives the aluminum tube a tough, abrasive-resitant surface.

6063-T832 Aluminum is used for pneumatic cylinder applications requiring very good corrosion resistance and/or light weight. Can also be used for low-pressure oil cylinders (250 psi or less).

  • No machining required on the ID
  • Seamless extruded and cold-drawn
  • Hard coated interior
  • Corrosion resistance
  • Good weldability

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$7.82
15-29$6.51
30-104$5.59
105+$4.34
/IN
at
Select Length
IN
-
IN

Grade 8 nylon insert lock nut. The thread size is
2 in – 12 UNF and the nominal hex is
3.125 in.

Grade 8 lock nuts have a nylon insert in the nut that allows the nut to grab the fastener. This keeps the nut from backing off due to vibration.

$21.73
/PC
1 in x 2 in x 0.5 in Bronze Tube | CRC Distribution Inc.

660-1000X2000 has a 0.5 in thick wall. The ID is 1 in and the OD is 2 in. The material is 660 Bronze Copper Alloy 932.

660 Bronze is used for machining bearings, bushings, wear strips, and plates. This grade of bronze is used in pump, cylinder, and machine tool applications.

  • Long life span
  • Machinability rating of 70
  • Not subject to dezincification

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-4$15.40
5-9$13.68
10-14$12.32
15+$11.21
/IN
at
Select Length
IN
-
IN

ALUM-2500 has a 2.5 in diameter. The material is 6061 Aluminum T6

6061 Aluminum T6 is suitable for machining pistons and head glands.

The T6 refers to the temper or degree of hardness. T6 has been solution heat treated and artificially aged to provide the maximum yield strength for a 6061 aluminum alloy.

  • Heat treated and aged for increased strength
  • Easily formed
  • Weldable
  • Corrosion resistant

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$5.40
15-29$3.86
30+$3.00
/IN
at
Select Length
IN
-
IN
  • « PREV
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • NEXT »