Search Results
Filter Your Search
Shop by Category
Hytrel backup ring with a flat cross-section.
Molded of 55D Durometer Hytrel, these back-up rings provide excellent extrusion resistance and tolerance to fluids such as phosphate esters, hydraulic oil and water. Stretched for installation, they return quickly to their original size for easy installation.
55D Durometer | Hytrel Material | 5 5/8 in Nominal Inner Diameter | 3/16 in Cross Section | Backup Ring
Features
- Improved extrusion resistance compared to standard FKM or NBR backups
- Can be stretched over larger diameters and will return quickly to their original size
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
Cast Iron Rod Clevis Mount with a 1 in – 14 TPI threaded end and a 1 in pin hole.
Clevis mounts help maintain alignment and protect the cylinder from side load. Mounts attach to threaded stud ends, pivot holes, or bolt holes on the cylinder. Can be used with hydraulic cylinders with standard bore sizes.
WR-NYL, 6 X 1/2 Wear Ring
O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.
70 Durometer | Buna-N Rubber Material | 7/8 in Nominal Inner Diameter | 1/16 in Cross Section | O-Ring
Features
- Pressure range varies according to diametral clearance
- Temperature range of -40 °F to -240 °F
Wear rings provide a hard-wearing surface that protects the cylinder walls and the piston rod from scoring and abrasion. By maintaining alignment and reducing side loads, these rings facilitate smoother piston movement and lower friction levels.
Nylon Material | 2 in Nominal Inner Diameter | 1/8 in Cross Section | Wear Ring
Features
- Protection Against Wear
- Reduced Friction
- Extended Cylinder Life
- Operational Efficiency
CIHT2240X2000 has a wall thickness of 0.12 in. The ID is 2 in and the OD is 2.24 in. The material is 1026 Carbon Steel with chrome plating on the Inside Surface.
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
1-14 | $4.76 |
15-29 | $3.41 |
30-74 | $2.64 |
75+ | $2.38 |
Hytrel backup ring with a flat cross-section.
Molded of 55D Durometer Hytrel, these back-up rings provide excellent extrusion resistance and tolerance to fluids such as phosphate esters, hydraulic oil and water. Stretched for installation, they return quickly to their original size for easy installation.
55D Durometer | Hytrel Material | 1 1/2 in Nominal Inner Diameter | 0.11 in Cross Section | Backup Ring
Features
- Improved extrusion resistance compared to standard FKM or NBR backups
- Can be stretched over larger diameters and will return quickly to their original size
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
CPO-3250 has a 3.25 in diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.
ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.
- Extremely smooth surface finish
- Excellent wear and corrosion resistance
- Good strength and impact properties
- Good machinability
- Reasonable weldability
- Fair response to normal heat treating and induction hardening practices
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
1-29 | $16.91 |
30-59 | $12.09 |
60-119 | $9.38 |
120-287 | $8.45 |
288+ | $7.69 |
Rubber Material | 1 1/16 in Nominal Inner Diameter | Wiper
Rubber Material | 1 1/16 in Nominal Inner Diameter | Wiper
MCPO-12 has a 12 mm diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.
ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.
- Extremely smooth surface finish
- Excellent wear and corrosion resistance
- Good strength and impact properties
- Good machinability
- Reasonable weldability
- Fair response to normal heat treating and induction hardening practices
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
1-29 | $2.17 |
30-59 | $1.08 |
60-89 | $0.93 |
90-134 | $0.72 |
135+ | $0.65 |