Search Results
Filter Your Search
Category Group
Shop by Category
Utilizing a sturdy metal case, these wipers are molded from the same high performance urethane used in our Heavy Duty U-seals. Built for severe service, these wipers are capable of surviving hostile environments.
92A Durometer | Urethane Material | 1 1/4 in Nominal Inner Diameter
Features
- Used in Heavy Duty U-seals
- Capable of surviving hostile environments
- Molded from the high performance urethane
The Hallite 533 is capable of withstanding high side loads and preventing metal-to-metal contact between the piston and the bore or the rod and the gland.
The PA 533 material is heat stabilised 33% glass reinforced nylon 66, which offers excellent bearing properties.
Compatible with hydraulic and lubricating oils. The PA 533 material is not recommended for use in water based fluids (HFA) or where significant water is present, due to the swell of the nylon.
AN wipers are ideal for light duty and pneumatic applications. Its main purpose is to prevent dirt and contaminants from entering the hydraulic or pneumatic systems. Suffix “SH” designates slotted heel design, “V” designates fluorocarbon material, and “B” designates carboxilated nitrile material.
90A Durometer | Urethane Material | 3 in Nominal Inner Diameter
Features
- Flexible, snap-in design for easy installation into closed housings
- Low compression set
O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.
70 Durometer | Buna-N Rubber Material | 13/16 in Nominal Inner Diameter | 3/32 in Cross Section | O-Ring
Features
- Pressure range varies according to diametral clearance
- Temperature range of -40 °F to -240 °F
O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.
70 Durometer | Buna-N Rubber Material | 2 5/8 in Nominal Inner Diameter | 1/8 in Cross Section | O-Ring
Features
- Pressure range varies according to diametral clearance
- Temperature range of -40 °F to -240 °F
MCPO-75 has a 75 mm diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.
ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.
- Extremely smooth surface finish
- Excellent wear and corrosion resistance
- Good strength and impact properties
- Good machinability
- Reasonable weldability
- Fair response to normal heat treating and induction hardening practices
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-29 | $15.52 |
| 30-74 | $11.10 |
| 75-134 | $8.61 |
| 135-287 | $7.76 |
| 288+ | $7.06 |
MCPO-90 has a 90 mm diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.
ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.
- Extremely smooth surface finish
- Excellent wear and corrosion resistance
- Good strength and impact properties
- Good machinability
- Reasonable weldability
- Fair response to normal heat treating and induction hardening practices
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-29 | $22.40 |
| 30-59 | $16.02 |
| 60-119 | $12.43 |
| 120-287 | $11.20 |
| 288+ | $10.19 |
O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.
70 Durometer | Buna-N Rubber Material | 7 3/4 in Nominal Inner Diameter | 1/8 in Cross Section | O-Ring
Features
- Pressure range varies according to diametral clearance
- Temperature range of -40 °F to -240 °F
O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.
70 Durometer | Buna-N Rubber Material | 1 1/2 in Nominal Inner Diameter | 3/32 in Cross Section | O-Ring
Features
- Pressure range varies according to diametral clearance
- Temperature range of -40 °F to -240 °F
O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.
70 Durometer | Buna-N Rubber Material | 1 3/4 in Nominal Inner Diameter | 3/32 in Cross Section | O-Ring
Features
- Pressure range varies according to diametral clearance
- Temperature range of -40 °F to -240 °F
