Browse Categories

Search Results

Filter Your Search

Show Attribute Category Group

Shop by Category

Loading...

Grade 8 nylon insert lock nut. The thread size is
2.5 in – 12 UNF and the nominal hex is
4 in.

Grade 8 lock nuts have a nylon insert in the nut that allows the nut to grab the fastener. This keeps the nut from backing off due to vibration.

$67.82
/PC

Female connection on both ends.

ORB fittings incorporate a port connection for leak prevention in medium and high pressure hydraulic systems. The female port has a straight thread and a machined surface, along with a chamfer where the o-ring is seated. The seal is created when the o-ring is compressed into the chamfer when mating the male and female connection providing a leak-tight seal.

$40.90
/PC

SBMM20ES has a 20 mm ID.

The bushing is Unsealed and made of forged steel. The ball will swivel like a fish eye with 3-5 degrees of movement.

$5.87
/PC

SBMM30ES has a 30 mm ID.

The bushing is Unsealed and made of forged steel. The ball will swivel like a fish eye with 3-5 degrees of movement.

$9.88
/PC

SBMM35ES-2RS has a 35 mm ID.

The bushing is Sealed and made of forged steel. The ball will swivel like a fish eye with 3-5 degrees of movement.

$8.04
/PC

GRT-80.00×5.90×2.00-C/S

$11.38
/EA

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70A Durometer | Nitrile Material | 110 MM Nominal Inner Diameter | 5 MM Cross Section | O-Ring

Features

  • Chemical resistance
  • Temperature range of -40 °F to 220 °F

$3.16
/EA

MHT-60X2.750 has a wall thickness of 4.925 mm. The ID is 60 mm and the OD is 69.85 mm. The material is 1026 Carbon Steel and has been stress-relieved and annealed.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$7.15
15-74$5.55
75-104$5.00
105+$4.55
/IN
at
Select Length
IN
-
IN

Asymmetric rod seal designed with precision trimmed sealing lips to provide a dry sealing solution in light and medium-duty applications. The Hallite 605 is molded in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation and excellent low temperature performance. The twin lip design helps solve difficult rod sealing problems by providing lower friction, increased stability, and high, dynamic lip force, while preventing air penetration from outside the cylinder. Designed to have interference in the seal housing groove and has a secondary lip. The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland. The inner dynamic lip is shorter and more robust to improve sealing and compression set characteristics over conventional, symmetrical U-seals.

The seal can be considered for use in heavy-duty applications when used with a suitable full depth back-up ring. The sealing lips are precision trimmed at an angle to give optimal rod sealing performance.

94A Durometer | Urethane Material | 1 1/4 in Nominal Inner Diameter | 1/4 in Cross Section | U-Seal

Features

  • General purpose rod seal
  • Robust design
  • Excellent wear resistance
  • Increase seal stability
  • Performs well over wide temperature range and is extremely effective in low temperatures
  • Primary lip protection
  • Easy to install

$11.02
/EA
4 5/8 X 4 7/8 X 1/8 O-ring NBR70(10) - 568-247 | CRC Distribution Inc.

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70 Durometer | Buna-N Rubber Material | 4 5/8 in Nominal Inner Diameter | 1/8 in Cross Section | O-Ring

Features

  • Pressure range varies according to diametral clearance
  • Temperature range of -40 °F to -240 °F

$1.34
/EA
  • « PREV
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • NEXT »