Search Results
Filter Your Search
Shop by Category
Wear rings provide a hard-wearing surface that protects the cylinder walls and the piston rod from scoring and abrasion. By maintaining alignment and reducing side loads, these rings facilitate smoother piston movement and lower friction levels.
Nylon Material | 4 3/4 in Nominal Inner Diameter | 1/8 in Cross Section | Wear Ring
Features
- Scarf Cut wear ring
- Protection Against Wear
- Reduced Friction
- Extended Cylinder Life
- Operational Efficiency
Parback® backup ring with a curved cross-section.
Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.
90A Durometer | Buna-N Rubber Material | 2 5/8 in Nominal Inner Diameter | 1/8 in Cross Section | Backup Ring
Features
- Excellent extrusion resistance
- Easily stretched for installation
- Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces
These seals are specifically designed with a second lip on their inside diameter and engineered to attain maximum, life and reliability in dynamic rod sealing. This feature results in reduced leakage, less friction, increased stability, and, prevents air and contaminants from entering the cylinder.
92A Durometer | Urethane Material | 1 1/4 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal
85mm induction hardened chrome shafting.
The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).
Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.
- Greater strength
- Better resistance to mechanical damage
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
1-29 | $18.92 |
30-59 | $13.53 |
60-119 | $10.50 |
120-287 | $9.46 |
288+ | $8.61 |
O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.
70 Durometer | Buna-N Rubber Material | 1 5/16 in Nominal Inner Diameter | 3/32 in Cross Section | O-Ring
Features
- Pressure range varies according to diametral clearance
- Temperature range of -40 °F to -240 °F
Parback® backup ring with a curved cross-section.
Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.
90A Durometer | Buna-N Rubber Material | 2 5/8 in Nominal Inner Diameter | 3/16 in Cross Section | Backup Ring
Features
- Excellent extrusion resistance
- Easily stretched for installation
- Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces
AN wipers are ideal for light duty and pneumatic applications. Its main purpose is to prevent dirt and contaminants from entering the hydraulic or pneumatic systems. Suffix “SH” designates slotted heel design, “V” designates fluorocarbon material, and “B” designates carboxilated nitrile material.
90A Durometer | Urethane Material | 2 1/2 in Nominal Inner Diameter
Features
- Flexible, snap-in design for easy installation into closed housings
- Low compression set
Parback® backup ring with a curved cross-section.
Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.
90A Durometer | Buna-N Rubber Material | 6 1/2 in Nominal Inner Diameter | 1/4 in Cross Section | Backup Ring
Features
- Excellent extrusion resistance
- Easily stretched for installation
- Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces
The PS1400 seals offer low friction and high strength in a compact double-acting piston seal design. The PTFE seal ring, combined with a rubber energizer, assures positive contact with the dynamic surface. The PS1400 is designed to fit ANSI/B93.32-1973 groove standards. Piston diameter “I” dimensions are given for pistons without wear rings.
15% Glass Filled PTFE Material | 2.608 in Nominal Inner Diameter | Piston Seal
Features
- Easy assembly
- Low friction capabilities