Search Results
Filter Your Search
Category Group
Shop by Category
Rubber Material | 1 3/4 in Nominal Inner Diameter | Wiper
Rubber Material | 1 3/4 in Nominal Inner Diameter | Wiper
Style ST-XL wipers are molded from premium urethane and are direct replacements for Style “ST” or “D” wipers. The outside diameter of the ring has a crush lip providing extra interference in the groove. A bead on the shoulder stops contaminates from entering through the groove. The inside diameter is ribbed to prevent pressure traps between the wiper and rod seal.
94A Durometer | Urethane Material | 1 5/8 in Nominal Inner Diameter
Features
- Crush lip to provide extra interference
- Bead on the shoulder to keep contaminants out
- Ribbed ID to prevent pressure traps
The PS1800 provides low friction, high strength piston sealing. The PS1800 also provides double-acting piston sealing in a compact design that meets the requirements of ANSI/B93-32-1973. Piston diameter “I” dimensions are given for pistons without wear rings.
15% Glass Filled PTFE Material | 3 15/16 in Nominal Inner Diameter | Piston Seal
Features
- Easy assembly
- Low friction capabilities
Asymmetric rod seal designed with precision trimmed sealing lips to provide a dry sealing solution in light and medium-duty applications. The Hallite 605 is molded in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation and excellent low temperature performance. The twin lip design helps solve difficult rod sealing problems by providing lower friction, increased stability, and high, dynamic lip force, while preventing air penetration from outside the cylinder. Designed to have interference in the seal housing groove and has a secondary lip. The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland. The inner dynamic lip is shorter and more robust to improve sealing and compression set characteristics over conventional, symmetrical U-seals.
The seal can be considered for use in heavy-duty applications when used with a suitable full depth back-up ring. The sealing lips are precision trimmed at an angle to give optimal rod sealing performance.
94A Durometer | Urethane Material | 2 1/4 in Nominal Inner Diameter | 1/4 in Cross Section | U-Seal
Features
- General purpose rod seal
- Robust design
- Excellent wear resistance
- Increase seal stability
- Performs well over wide temperature range and is extremely effective in low temperatures
- Primary lip protection
- Easy to install
The PS1850 piston seal can be used interchangeably with the PS1800 style piston seal. This seal provides improved heat resistance for demanding applications. Piston diameter “I” dimensions are given for pistons without wear rings.
Bronze Filled PTFE Material | 2 15/16 in Nominal Inner Diameter | Piston Seal
Features
- Easy assembly
- Low friction capabilities
Heavy duty chain vise designed to secure and clamp hydraulic cylinders during teardown and assembly.
The chain vise secures cylinders up to 20 in.
The vise uses 2.5-inch wide chains to secure cylinders in place. Once secured, the cylinder will not move as it is disassembled or while the gland is being removed.
Order a pair to safely work on longer cylinders. Add an oil pan underneath to collect the oil easily.
Chain vise only. Stand sold separately.
Wear rings provide a hard-wearing surface that protects the cylinder walls and the piston rod from scoring and abrasion. By maintaining alignment and reducing side loads, these rings facilitate smoother piston movement and lower friction levels.
Nylon Material | 2 1/4 in Nominal Inner Diameter | 1/8 in Cross Section | Wear Ring
Features
- Scarf Cut wear ring
- Protection Against Wear
- Reduced Friction
- Extended Cylinder Life
- Operational Efficiency
O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.
90 Durometer | Buna-N Rubber Material | 4 1/2 in Nominal Inner Diameter | 1/8 in Cross Section | O-Ring
Features
- Pressure range varies according to diametral clearance
- Temperature range of -40 °F to -240 °F
Hytrel backup ring with a flat cross-section.
Molded of 55D Durometer Hytrel, these back-up rings provide excellent extrusion resistance and tolerance to fluids such as phosphate esters, hydraulic oil and water. Stretched for installation, they return quickly to their original size for easy installation.
55D Durometer | Hytrel Material | 3 1/8 in Nominal Inner Diameter | 3/16 in Cross Section | Backup Ring
Features
- Improved extrusion resistance compared to standard FKM or NBR backups
- Can be stretched over larger diameters and will return quickly to their original size
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
