Browse Categories

Search Results

Filter Your Search

Show Attribute Category Group

Shop by Category

Loading...

CPOD1750X654 has a wall thickness of 0.548 in. The ID is 0.654 in and the OD is 1.75 in. The material is 1026 Carbon Steel with chrome plating on the Outside Surface.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$10.60
15-29$8.82
30-59$6.63
60-104$5.88
105+$5.30
/IN
at
Select Length
IN
-
IN
6 1/2 X 6 3/4 X 1/8 O-ring NBR70 - 568-260 | CRC Distribution Inc.

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70 Durometer | Buna-N Rubber Material | 6 1/2 in Nominal Inner Diameter | 1/8 in Cross Section | O-Ring

Features

  • Pressure range varies according to diametral clearance
  • Temperature range of -40 °F to -240 °F

$2.29
/EA

The Hallite 533 is capable of withstanding high side loads and preventing metal-to-metal contact between the piston and the bore or the rod and the gland.

The PA 533 material is heat stabilised 33% glass reinforced nylon 66, which offers excellent bearing properties.

Compatible with hydraulic and lubricating oils. The PA 533 material is not recommended for use in water based fluids (HFA) or where significant water is present, due to the swell of the nylon.

$17.58
/EA

Rubber Material | 2 in Nominal Inner Diameter | Wiper

Rubber Material | 2 in Nominal Inner Diameter | Wiper

$6.27
/EA

Utilizing a sturdy metal case, these wipers are molded from the same high performance urethane used in our Heavy Duty U-seals. Built for severe service, these wipers are capable of surviving hostile environments.

92A Durometer | Urethane Material | 2 in Nominal Inner Diameter

Features

  • Used in Heavy Duty U-seals
  • Capable of surviving hostile environments
  • Molded from the high performance urethane

$19.92
/EA

Utilizing a sturdy metal case, these wipers are molded from the same high performance urethane used in our Heavy Duty U-seals. Built for severe service, these wipers are capable of surviving hostile environments.

92A Durometer | Urethane Material | 3 1/2 in Nominal Inner Diameter

Features

  • Used in Heavy Duty U-seals
  • Capable of surviving hostile environments
  • Molded from the high performance urethane

$33.75
/EA

GB-TFE-9.5×2.5

$34.69
/FT

US-90URE-2-5/8×2-7/8×1/8

$7.89
/EA
PB12-300-050-SC Powerband | CRC Distribution Inc.

Hercules® Sealing Products is pleased to introduce our new line of PowerbandTM tight tolerance premium wearrings. Manufactured from a highly engineered blend of premium nylon, glass fiber, and PTFE, PowerbandsTM offer a high strength wear-ring for all cylinder applications, including those with minimal lubrication. And, with a Coefficient of Friction nearly 50% lower than our standard product, your cylinders will run smoother and more efficiently than ever. All PowerbandsTM are fully machined with cross-section tolerances of only ±0.001”, chamfered corners, and scarf or angle-cut end gaps. Compared to standard tolerances of ±0.0025”, this tightened tolerance improves the alignment and concentric operation of cylinder rods and pistons. The fully machined chamfered corners will better accommodate cylinder housing grooves, further improving piston and rod alignment. Lastly, the scarf-cut end gap reduces the loss of bearing support that may occur during cylinder side-loading. When combined, these features reduce the tolerance stack-up within the components of the cylinder. As a result, your cylinders will operate more consistently and be capable of operating at higher pressures and higher side loads than with standard wear-ring products. Furthermore, with this improved cylinder operation, your seals will last longer and the life of your cylinder will be extended. PowerbandsTM are currently available in our most popular wear-ring dimensions.

2 3/4 in Nominal Inner Diameter | Powerband

Features

  • PowerbandsTM offer a high strength wear-ring for all cylinder applications
  • Fully machined with cross-section tolerances of only ±0.001
  • Chamfered corners
  • Scarf or angle-cut end gaps

$8.55
/EA

DUCT-8000 has a diameter of 8 in. The material is 65-45-12 Ductile Iron.

65-45-12 Ductile Iron is used to machine pistons, glands, caps, manifolds, rams, and valve bodies.

Ductile has higher machining speeds than steel and there is usually no need for deburring machined parts. The graphite flakes in the material act as a self-lubricant. Ductile can be flame or induction hardened as well as deep hardened.

Ductile bars are produced with sufficient stock on the outside diameter to ensure clean-up at the nominal dimension.

  • Excellent machinability
  • Optimal impact strengths
  • Optimal fatigue properties
  • Optimal electrical conductivity
  • High magnetic permeability

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-9$50.61
10-39$44.94
40+$36.84
/IN
at
Select Length
IN
-
IN
  • « PREV
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • NEXT »