Browse Categories

Search Results

Filter Your Search

Show Attribute Category Group

Shop by Category

Loading...

Asymmetric rod seal designed with precision trimmed sealing lips to provide a dry sealing solution in light and medium-duty applications. The Hallite 605 is molded in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation and excellent low temperature performance. The twin lip design helps solve difficult rod sealing problems by providing lower friction, increased stability, and high, dynamic lip force, while preventing air penetration from outside the cylinder. Designed to have interference in the seal housing groove and has a secondary lip. The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland. The inner dynamic lip is shorter and more robust to improve sealing and compression set characteristics over conventional, symmetrical U-seals.

The seal can be considered for use in heavy-duty applications when used with a suitable full depth back-up ring. The sealing lips are precision trimmed at an angle to give optimal rod sealing performance.

94A Durometer | Urethane Material | 1 1/4 in Nominal Inner Diameter | 1/4 in Cross Section | U-Seal

Features

  • General purpose rod seal
  • Robust design
  • Excellent wear resistance
  • Increase seal stability
  • Performs well over wide temperature range and is extremely effective in low temperatures
  • Primary lip protection
  • Easy to install

$11.02
/EA

DUCT-6500 has a diameter of 6.5 in. The material is 65-45-12 Ductile Iron.

65-45-12 Ductile Iron is used to machine pistons, glands, caps, manifolds, rams, and valve bodies.

Ductile has higher machining speeds than steel and there is usually no need for deburring machined parts. The graphite flakes in the material act as a self-lubricant. Ductile can be flame or induction hardened as well as deep hardened.

Ductile bars are produced with sufficient stock on the outside diameter to ensure clean-up at the nominal dimension.

  • Excellent machinability
  • Optimal impact strengths
  • Optimal fatigue properties
  • Optimal electrical conductivity
  • High magnetic permeability

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-9$33.64
10-39$29.87
40+$24.49
/IN
at
Select Length
IN
-
IN
O-ring | CRC Distribution Inc.

O-ring

90 Durometer | Buna-N Rubber Material | 0.924 in Nominal Inner Diameter | 0.116 in Cross Section | O-Ring Boss Gasket

$0.41
/EA

The Hallite 533 is capable of withstanding high side loads and preventing metal-to-metal contact between the piston and the bore or the rod and the gland.

The PA 533 material is heat stabilised 33% glass reinforced nylon 66, which offers excellent bearing properties.

Compatible with hydraulic and lubricating oils. The PA 533 material is not recommended for use in water based fluids (HFA) or where significant water is present, due to the swell of the nylon.

$17.58
/EA

5 Packing & Wiper

$51.43
/EA

Style 850 u-seals offer excellent resistance to extrusion and abrasion. The round cross-section expander offers energized sealing from zero to 5,000 psi.

95A Durometer | Urethane Material | 1 1/4 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal

$7.37
/EA
PS, 3.500 X 3.108 X 0.129 URE - PS1500-56 | CRC Distribution Inc.

Totally interchangeable with Style PS1400 PTFE piston seals, Style PS1500 piston seals are molded from tough 60 Shore D durometer polyurethane. During the molding process, a .002” thick band of molybdenum disulfide is molded into the outside diameter of the seal ring for reduced friction. PS1500 piston seals are easily stretched over the piston and recover rapidly with the elimination of the “cold flow” characteristics found in PTFE seals. Piston diameter “I” dimensions are given for pistons without wear rings.

60 Shore D Durometer | Polyurethane Material | 3.106 in Nominal Inner Diameter | Piston Seal

Features

  • Easy assembly
  • Low friction capabilities

$6.65
/EA

Style ST-XL wipers are molded from premium urethane and are direct replacements for Style “ST” or “D” wipers. The outside diameter of the ring has a crush lip providing extra interference in the groove. A bead on the shoulder stops contaminates from entering through the groove. The inside diameter is ribbed to prevent pressure traps between the wiper and rod seal.

94A Durometer | Urethane Material | 2 3/4 in Nominal Inner Diameter

Features

  • Crush lip to provide extra interference
  • Bead on the shoulder to keep contaminants out
  • Ribbed ID to prevent pressure traps

$8.12
/EA
3 X 3 3/16 X 3/32 O-ring NBR70 - 568-151 | CRC Distribution Inc.

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70 Durometer | Buna-N Rubber Material | 3 in Nominal Inner Diameter | 3/32 in Cross Section | O-Ring

Features

  • Pressure range varies according to diametral clearance
  • Temperature range of -40 °F to -240 °F

$0.65
/EA
4 X 4 3/16 X 3/32 O-ring NBR70 - 568-155 | CRC Distribution Inc.

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70 Durometer | Buna-N Rubber Material | 4 in Nominal Inner Diameter | 3/32 in Cross Section | O-Ring

Features

  • Pressure range varies according to diametral clearance
  • Temperature range of -40 °F to -240 °F

$1.06
/EA
  • « PREV
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • NEXT »