Browse Categories

Search Results

Filter Your Search

Show Attribute Category Group

Shop by Category

Loading...
7 1/2 X 7 3/4 X 1/8 O-ring NBR70 - 568-264 | CRC Distribution Inc.

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70 Durometer | Buna-N Rubber Material | 7 1/2 in Nominal Inner Diameter | 1/8 in Cross Section | O-Ring

Features

  • Pressure range varies according to diametral clearance
  • Temperature range of -40 °F to -240 °F

$2.98
/EA
O-ring | CRC Distribution Inc.

O-ring

90 Durometer | Buna-N Rubber Material | 0.644 in Nominal Inner Diameter | 0.087 in Cross Section | O-Ring Boss Gasket

$0.31
/EA

Hytrel backup ring with a flat cross-section.

Molded of 55D Durometer Hytrel, these back-up rings provide excellent extrusion resistance and tolerance to fluids such as phosphate esters, hydraulic oil and water. Stretched for installation, they return quickly to their original size for easy installation.

55D Durometer | Hytrel Material | 3 1/8 in Nominal Inner Diameter | 3/16 in Cross Section | Backup Ring

Features

  • Improved extrusion resistance compared to standard FKM or NBR backups
  • Can be stretched over larger diameters and will return quickly to their original size
  • High strength and abrasion resistance
  • Wide temperature range
  • Chemical resistance
  • Low friction
  • Easy installation

$1.56
/EA

Parback® backup ring with a curved cross-section.

Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.

90A Durometer | Buna-N Rubber Material | 2 in Nominal Inner Diameter | 1/8 in Cross Section | Backup Ring

Features

  • Excellent extrusion resistance
  • Easily stretched for installation
  • Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces

$1.01
/EA

Style ST-XL wipers are molded from premium urethane and are direct replacements for Style “ST” or “D” wipers. The outside diameter of the ring has a crush lip providing extra interference in the groove. A bead on the shoulder stops contaminates from entering through the groove. The inside diameter is ribbed to prevent pressure traps between the wiper and rod seal.

94A Durometer | Urethane Material | 1 5/8 in Nominal Inner Diameter

Features

  • Crush lip to provide extra interference
  • Bead on the shoulder to keep contaminants out
  • Ribbed ID to prevent pressure traps

$5.92
/EA

CPO-5000 has a 5 in diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.

ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.

  • Extremely smooth surface finish
  • Excellent wear and corrosion resistance
  • Good strength and impact properties
  • Good machinability
  • Reasonable weldability
  • Fair response to normal heat treating and induction hardening practices

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-14$41.35
15-29$29.56
30-59$25.84
60-119$20.67
120+$18.81
/IN
at
Select Length
IN
-
IN

Molded in PTFE with a rubber energizer, this seal absorbs the shock of pressure spikes to protect the rod seal.

70A Durometer | Filled PTFE Buffer Material | 45 MM Nominal Inner Diameter | Buffer Seal

$18.78
/EA

Molded from filled PTFE and machined to close tolerances, these seals feature low friction and excellent wear characteristics. Nitrile rings are used for energizers.

70A Durometer | PTFE Material | 54.5 MM Nominal Inner Diameter | Piston Seal

Features

  • Easy assembly
  • Low friction capabilities

$33.20
/EA

DUCT-5500 has a diameter of 5.5 in. The material is 65-45-12 Ductile Iron.

65-45-12 Ductile Iron is used to machine pistons, glands, caps, manifolds, rams, and valve bodies.

Ductile has higher machining speeds than steel and there is usually no need for deburring machined parts. The graphite flakes in the material act as a self-lubricant. Ductile can be flame or induction hardened as well as deep hardened.

Ductile bars are produced with sufficient stock on the outside diameter to ensure clean-up at the nominal dimension.

  • Excellent machinability
  • Optimal impact strengths
  • Optimal fatigue properties
  • Optimal electrical conductivity
  • High magnetic permeability

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-9$24.03
10-39$21.34
40+$17.50
/IN
at
Select Length
IN
-
IN

M-RK-P-UB-1-50MM

$57.66
/EA
  • « PREV
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • NEXT »