Browse Categories

Search Results

Filter Your Search

Show Attribute Category Group

Shop by Category

Loading...
7 1/4 X 7 1/2 X 1/8 O-ring NBR70 - 568-263 | CRC Distribution Inc.

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70 Durometer | Buna-N Rubber Material | 7 1/4 in Nominal Inner Diameter | 1/8 in Cross Section | O-Ring

Features

  • Pressure range varies according to diametral clearance
  • Temperature range of -40 °F to -240 °F

$2.76
/EA

Parback® backup ring with a curved cross-section.

Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.

90A Durometer | Buna-N Rubber Material | 2 7/8 in Nominal Inner Diameter | 1/8 in Cross Section | Backup Ring

Features

  • Excellent extrusion resistance
  • Easily stretched for installation
  • Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces

$1.49
/EA

Wear rings provide a hard-wearing surface that protects the cylinder walls and the piston rod from scoring and abrasion. By maintaining alignment and reducing side loads, these rings facilitate smoother piston movement and lower friction levels.

Nylon Material | 2 in Nominal Inner Diameter | 1/8 in Cross Section | Wear Ring

Features

  • Protection Against Wear
  • Reduced Friction
  • Extended Cylinder Life
  • Operational Efficiency

$8.40
/EA

Wear rings provide a hard-wearing surface that protects the cylinder walls and the piston rod from scoring and abrasion. By maintaining alignment and reducing side loads, these rings facilitate smoother piston movement and lower friction levels.

Nylon Material | 6 in Nominal Inner Diameter | 1/8 in Cross Section | Wear Ring

Features

  • Protection Against Wear
  • Reduced Friction
  • Extended Cylinder Life
  • Operational Efficiency

$22.67
/EA
RW-90URE-1x1.272x0.104 - AN-09-SH | CRC Distribution Inc.

Suffix “SH” designates slotted heel design, “V” designates fluorocarbon material, and “B” designates carboxilated nitrile material.

90A Durometer | Urethane Material | 1 in Nominal Inner Diameter

Features

  • Slotted heel design
  • Slots in the heel allow excess hydraulic fluid to bypass the wiper

$1.90
/EA

CPIN-STL-2-1/2×5/32

$1.09
/EA
US-90URE-3-1/4x4x3/8 - DSU37-3.25-37 | CRC Distribution Inc.

Used interchangeably for piston or rod sealing, these u-seals employ the same tough urethane material found in our, Heavy Duty Rod and Piston U-Seals.

92A Durometer | Urethane Material | 3 1/4 in Nominal Inner Diameter | 3/8 in Cross Section | U-Seal

$25.81
/EA

DUCT-7500 has a diameter of 7.5 in. The material is 65-45-12 Ductile Iron.

65-45-12 Ductile Iron is used to machine pistons, glands, caps, manifolds, rams, and valve bodies.

Ductile has higher machining speeds than steel and there is usually no need for deburring machined parts. The graphite flakes in the material act as a self-lubricant. Ductile can be flame or induction hardened as well as deep hardened.

Ductile bars are produced with sufficient stock on the outside diameter to ensure clean-up at the nominal dimension.

  • Excellent machinability
  • Optimal impact strengths
  • Optimal fatigue properties
  • Optimal electrical conductivity
  • High magnetic permeability

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1-9$44.95
10-39$39.92
40+$32.72
/IN
at
Select Length
IN
-
IN
7/16 X 9/16 X 1/16 O-ring NBR70 - 568-013 | CRC Distribution Inc.

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70 Durometer | Buna-N Rubber Material | 7/16 in Nominal Inner Diameter | 1/16 in Cross Section | O-Ring

Features

  • Pressure range varies according to diametral clearance
  • Temperature range of -40 °F to -240 °F

$0.06
/EA
1 1/2 X 1 3/4 X 1/8  O-ring NBR 90(20) - 568-222-90D | CRC Distribution Inc.

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

90 Durometer | Buna-N Rubber Material | 1 1/2 in Nominal Inner Diameter | 1/8 in Cross Section | O-Ring

Features

  • Pressure range varies according to diametral clearance
  • Temperature range of -40 °F to -240 °F

$0.62
/EA
  • « PREV
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • NEXT »