Search Results
Filter Your Search
Shop by Category
MHT-60X70 has a wall thickness of 5 mm. The ID is 60 mm and the OD is 70 mm. The material is 1026 Carbon Steel and has been stress-relieved and annealed.
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
1-14 | $6.41 |
15-74 | $4.97 |
75-104 | $4.48 |
105+ | $4.08 |
Molded in a tough urethane, this seal employs an additional lip near the heel. The twin lip design provides stability, friction-reducing lube retention, and some contaminant resistance. VME – Secondary lip is further from heel than standard MRTU. NOTE: E = European Urethane.
Urethane Material | 50 MM Nominal Inner Diameter | Rod U-Seal
Features
- Excellent low temperature performance
- Easy installation
Style 850 u-seals offer excellent resistance to extrusion and abrasion. The round cross-section expander offers energized sealing from zero to 5,000 psi.
95A Durometer | Urethane Material | 5 1/2 in Nominal Inner Diameter | 7/32 in Cross Section | U-Seal
The PS1400 seals offer low friction and high strength in a compact double-acting piston seal design. The PTFE seal ring, combined with a rubber energizer, assures positive contact with the dynamic surface. The PS1400 is designed to fit ANSI/B93.32-1973 groove standards. Piston diameter “I” dimensions are given for pistons without wear rings.
15% Glass Filled PTFE Material | 1.24 in Nominal Inner Diameter | Piston Seal
Features
- Easy assembly
- Low friction capabilities
The PS1400 seals offer low friction and high strength in a compact double-acting piston seal design. The PTFE seal ring, combined with a rubber energizer, assures positive contact with the dynamic surface. The PS1400 is designed to fit ANSI/B93.32-1973 groove standards. Piston diameter “I” dimensions are given for pistons without wear rings.
15% Glass Filled PTFE Material | 4.608 in Nominal Inner Diameter | Piston Seal
Features
- Easy assembly
- Low friction capabilities
Piston diameter “I” dimensions are given for pistons without wear rings.
15% Glass Filled PTFE Material | 2.223 in Nominal Inner Diameter | Piston Seal
Features
- Easy assembly
- Low friction capabilities
Molded from a PTFE base material with 40% bronze and machined to exacting tolerances, this seal exhibits low friction and high strength corners are chamfered for cold flow resistance.
40% Bronze Filled PTFE Material | 3 3/8 in Nominal Inner Diameter | Piston Seal
Features
- Easy assembly
- Low friction capabilities
Molded from 93 Shore A polyurethane with a 70 Shore A energizer, this seal utilizes the same groove dimensions as a standard o-ring or T-seal. One or two Style 575 back-up rings may be used for wider grooves. Extrusion resistant by design, this seal is also resistant to rolling and twisting. Installation is an easy two step snap-in procedure with no need to re-size before insertion into the bore. Piston diameter “I” dimensions are given for pistons without wear rings.
93A; 70A Durometer | Urethane Material | 3 1/8 in Nominal Inner Diameter | Piston Seal
Features
- Easy assembly
- Low friction capabilities
Wear rings provide a hard-wearing surface that protects the cylinder walls and the piston rod from scoring and abrasion. By maintaining alignment and reducing side loads, these rings facilitate smoother piston movement and lower friction levels.
Nylon Material | 2 in Nominal Inner Diameter | 1/8 in Cross Section | Wear Ring
Features
- Protection Against Wear
- Reduced Friction
- Extended Cylinder Life
- Operational Efficiency