Wipers
Filter Your Search
Shop by Category
AN wipers are ideal for light duty and pneumatic applications. Its main purpose is to prevent dirt and contaminants from entering the hydraulic or pneumatic systems. Suffix “SH” designates slotted heel design, “V” designates fluorocarbon material, and “B” designates carboxilated nitrile material.
90A Durometer | Urethane Material | 3 5/8 in Nominal Inner Diameter
Features
- Flexible, snap-in design for easy installation into closed housings
- Low compression set
Buna-N Material | 1 1/4 in Nominal Inner Diameter | Wiper
Buna-N Material | 1 1/4 in Nominal Inner Diameter | Wiper
Buna-N Material | 3 in Nominal Inner Diameter | Wiper
Buna-N Material | 3 in Nominal Inner Diameter | Wiper
Style ST-XL wipers are molded from premium urethane and are direct replacements for Style “ST” or “D” wipers. The outside diameter of the ring has a crush lip providing extra interference in the groove. A bead on the shoulder stops contaminates from entering through the groove. The inside diameter is ribbed to prevent pressure traps between the wiper and rod seal.
94A Durometer | Urethane Material | 1 3/16 in Nominal Inner Diameter
Features
- Crush lip to provide extra interference
- Bead on the shoulder to keep contaminants out
- Ribbed ID to prevent pressure traps
The Hallite 820 single-lipped, snap-in rod wiper is designed to fit North American D-style housings and has been developed specifically for use in harsher environments with heavy contamination, such as in agriculture, off-highway, and forestry equipment. These wipers include a dust lip to prevent contaminates from entering through the groove. They also have a ribbed inside diameter for low friction operation and to prevent pressure traps between the wiper and rod seal.
93A Durometer | Urethane Material | 3 in Nominal Inner Diameter
Features
- Umbrella Wiper Technology™
- Reducing corrosion and preventing the ingress of contamination into the wiper housing groove and hydraulic cylinder gland which will result in increased system life.
- Moulded ribs on the internal diameter
- Easy to install without the use of special tooling
- Normally specified for harsh environments
Style ST wiper rings are precision molded from 90A durometer urethane. Flexible enough to easily snap into a groove yet tough enough to handle difficult rod wiping applications. “V” tagged wipers are constructed of fluorocarbon.
90A Durometer | Urethane Material | 3/8 in Nominal Inner Diameter
Features
- Flexible enough to snap into a groove
- Wipers are constructed of fluorocarbon
Style ST wiper rings are precision molded from 90A durometer urethane. Flexible enough to easily snap into a groove yet tough enough to handle difficult rod wiping applications. “V” tagged wipers are constructed of fluorocarbon.
90A Durometer | Urethane Material | 4 in Nominal Inner Diameter
Features
- Flexible enough to snap into a groove
- Wipers are constructed of fluorocarbon
Style ST wiper rings are precision molded from 90A durometer urethane. Flexible enough to easily snap into a groove yet tough enough to handle difficult rod wiping applications. “V” tagged wipers are constructed of fluorocarbon.
90A Durometer | Urethane Material | 4 1/4 in Nominal Inner Diameter
Features
- Flexible enough to snap into a groove
- Wipers are constructed of fluorocarbon
RW-PE-5.000×5.750×0.375
Each Seal Guard Wiper consists of two flexible bronze rings which are held in place by a nitrile cushion ring. The cushion ring absorbs side loads and energizes the wiper to maintain close contact with the rod. Particularly suited for hostile environments, seal guard wipers shave off sand, grift, slag, flux, paint, moisture, chips and slivers. Seal Guard Wipers are long-lasting, self-adjusting, and offer low friction. Seal Guard Wipers can be installed in standard Hercules® Sealing Products “ST” or “D” Style grooves by increasing the “F” gland dimension to the “F” Throat Diameter shown.
70A Durometer | 660 Bronze; Nitrile Material | 2 1/2 in Nominal Inner Diameter | Wiper