Piston Seals

This capped piston seal consists of a filled PTFE cap, a T-shaped NBR energizer, and two split nylon backup rings. It exhibits low friction, high sealability, and excellent resistance to extrusion and wear.

PTFE Material | 75 MM Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities

Totally interchangeable with Style PS1400 PTFE piston seals, Style PS1500 piston seals are molded from tough 60 Shore D durometer polyurethane. During the molding process, a .002” thick band of molybdenum disulfide is molded into the outside diameter of the seal ring for reduced friction. PS1500 piston seals are easily stretched over the piston and recover rapidly with the elimination of the “cold flow” characteristics found in PTFE seals. Piston diameter “I” dimensions are given for pistons without wear rings.

60 Shore D Durometer | Polyurethane Material | 1.36 in Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities

Designed to fit on one or two piece pistons, this piston seal employs a nitrile seal for high sealability, nylon split backups for extrusion resistance, and two split bearing rings. No further support bearings are required.

90A Durometer | Nitrile Material | 1 3/8 in Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities

Our Style PSU piston seal, or uniring, is a laminated one piece double acting seal made of cast polyurethane. The tough outer layer is highly resistant to abrasion and is impregnated with molybdenum disulfide to reduce friction. The softer inner layer acts as a static seal and also energizes the OD to make full contact with the bore. This seal may be used to replace an existing Uniring or other seals of the same dimensions – O-rings, O-rings with back-ups, T-seals, U-seals, etc. Piston diameter “I” dimensions are given for pistons without wear rings.

60D & 57A Durometer | Urethane Composite Material | 3 1/2 in Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities

A double acting piston seal with many features: Two compact seal edges to concentrate the load against the dynamic surface, a cavity between the two external seal edges to retain fluid (reducing friction and wear), side grooves to allow pressure to load the energizer in all working conditions, high sealing performance at low pressure, excellent wear-resistance, and high resistance against extrusion.

97A; 70A Durometer | Urethane Material | 39 MM Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities

Piston diameter “I” dimensions are given for pistons without wear rings.

15% Glass Filled PTFE Material | 2.353 in Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities

Piston diameter “I” dimensions are given for pistons without wear rings.

15% Glass Filled PTFE Material | 3.353 in Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities

Totally interchangeable with Style PS1400 PTFE piston seals, Style PS1500 piston seals are molded from tough 60 Shore D durometer polyurethane. During the molding process, a .002” thick band of molybdenum disulfide is molded into the outside diameter of the seal ring for reduced friction. PS1500 piston seals are easily stretched over the piston and recover rapidly with the elimination of the “cold flow” characteristics found in PTFE seals. Piston diameter “I” dimensions are given for pistons without wear rings.

60 Shore D Durometer | Polyurethane Material | 4.106 in Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities

The PS1800 provides low friction, high strength piston sealing. The PS1800 also provides double-acting piston sealing in a compact design that meets the requirements of ANSI/B93-32-1973. Piston diameter “I” dimensions are given for pistons without wear rings.

15% Glass Filled PTFE Material | 3 3/16 in Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities

This two piece piston seal design comes made with a heat-stabilized, thermoplastic step-cut ring along with a profiled NBR energizer. This product offers extreme strength and resistance to extrusion, a very high resistance to abrasion, and ease of installation thanks to the step cut design and chamfered edges. The design also allows the seal to pass over ports without damage and offers greater resistance to surface roughness in comparison to any elastomer seals. The profiled energizer offers improved dynamic sealing ability, responding quickly to pressure changes and providing excellent sealing characteristics under a wide range of pressure conditions.

Glass Filled Nylon Material | 3.908 in Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities