Search Results
Filter Your Search
Category Group
Shop by Category
WR-NYL, 3 X 1 Wear Ring NYL
Wear rings provide a hard-wearing surface that protects the cylinder walls and the piston rod from scoring and abrasion. By maintaining alignment and reducing side loads, these rings facilitate smoother piston movement and lower friction levels.
Nylon Material | 3 in Nominal Inner Diameter | 1/8 in Cross Section | Wear Ring
Features
- Protection Against Wear
- Reduced Friction
- Extended Cylinder Life
- Operational Efficiency
Solid Urethane backup ring with a flat cross-section.
95A Durometer | Urethane Material | 10 in Nominal Inner Diameter | 1/4 in Cross Section | Backup Ring
Features
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
12 X 12 1/2 Back-up SOLID PTFE
Wear rings provide a hard-wearing surface that protects the cylinder walls and the piston rod from scoring and abrasion. By maintaining alignment and reducing side loads, these rings facilitate smoother piston movement and lower friction levels.
Nylon Material | 4 1/4 in Nominal Inner Diameter | 1/8 in Cross Section | Wear Ring
Features
- Scarf Cut wear ring
- Protection Against Wear
- Reduced Friction
- Extended Cylinder Life
- Operational Efficiency
Style 590 Back-up Rings feature exceptional strength and abrasion resistance along with a 53 Shore D hardness rating which makes them suitable for high pressure service where extrusion is a problem. Primarily used as a u-seal back-up, these rings can be used with o-rings. They also retrofit urethane and PTFE back-up rings, with greater performance characteristics. “S” suffix designates a split ring.
53 Shore D Durometer | Hytrel Material | 1 3/4 in Nominal Inner Diameter | 3/16 in Cross Section | Backup Ring
Features
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
Style 590 Back-up Rings feature exceptional strength and abrasion resistance along with a 53 Shore D hardness rating which makes them suitable for high pressure service where extrusion is a problem. Primarily used as a u-seal back-up, these rings can be used with o-rings. They also retrofit urethane and PTFE back-up rings, with greater performance characteristics. “S” suffix designates a split ring.
53 Shore D Durometer | Hytrel Material | 2 in Nominal Inner Diameter | 3/16 in Cross Section | Backup Ring
Features
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
Style 614 rod bearings are available in nylon material. These products are used extensively in hydraulic cylinders due to their low rate of wear and non-scoring properties. Excellent for those heavy duty applications that require a sturdy bearing.
Nylon Material | 4 in Nominal Inner Diameter | 1/4 in Cross Section | Rod Bearing
Used primarily as an anti-extrusion device for u-seals, these back-up rings combine high performance with very low friction. “ST” suffix designates a split ring.
PTFE Material | 4 1/2 in Nominal Inner Diameter | Backup Ring
Features
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
660-1500X3000 has a 0.75 in thick wall. The ID is 1.5 in and the OD is 3 in. The material is 660 Bronze Copper Alloy 932.
660 Bronze is used for machining bearings, bushings, wear strips, and plates. This grade of bronze is used in pump, cylinder, and machine tool applications.
- Long life span
- Machinability rating of 70
- Not subject to dezincification
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-4 | $31.52 |
| 5-9 | $27.99 |
| 10-14 | $25.22 |
| 15+ | $22.95 |
