Search Results
Filter Your Search
Category Group
Shop by Category
CIHT2250X2000 has a wall thickness of 0.125 in. The ID is 2 in and the OD is 2.25 in. The material is 1026 Carbon Steel with chrome plating on the Inside Surface.
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-14 | $6.80 |
| 15-29 | $4.86 |
| 30-74 | $3.77 |
| 75+ | $3.40 |
Used primarily as an anti-extrusion device for u-seals, these back-up rings combine high performance with very low friction. “ST” suffix designates a split ring.
PTFE Material | 2 in Nominal Inner Diameter | Backup Ring
Features
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
RWAN, 1 X 1.274 X .107 AN POLYESTER
Suffix “SH” designates slotted heel design, “V” designates fluorocarbon material, and “B” designates carboxilated nitrile material.
90A Durometer | Urethane Material | 2 in Nominal Inner Diameter
Features
- Slotted heel design
- Slots in the heel allow excess hydraulic fluid to bypass the wiper
AN wipers are ideal for light duty and pneumatic applications. Its main purpose is to prevent dirt and contaminants from entering the hydraulic or pneumatic systems.
AN wipers will retrofit into glands prescribed in MS-33675 for corresponding dash numbers of MS-28776.
- Flexible, snap-in design for easy installation into closed housings
- Low compression set
AN wipers are ideal for light duty and pneumatic applications. Its main purpose is to prevent dirt and contaminants from entering the hydraulic or pneumatic systems. Suffix “SH” designates slotted heel design, “V” designates fluorocarbon material, and “B” designates carboxilated nitrile material.
90A Durometer | Urethane Material | 3 7/8 in Nominal Inner Diameter
Features
- Flexible, snap-in design for easy installation into closed housings
- Low compression set
AN wipers are ideal for light duty and pneumatic applications. Its main purpose is to prevent dirt and contaminants from entering the hydraulic or pneumatic systems. Suffix “SH” designates slotted heel design, “V” designates fluorocarbon material, and “B” designates carboxilated nitrile material.
90A Durometer | Urethane Material | 7 in Nominal Inner Diameter
Features
- Flexible, snap-in design for easy installation into closed housings
- Low compression set
COMM, 6 3/4 Flat 1 Bearing NYL
CPO-3625 has a 3.625 in diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.
ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.
- Extremely smooth surface finish
- Excellent wear and corrosion resistance
- Good strength and impact properties
- Good machinability
- Reasonable weldability
- Fair response to normal heat treating and induction hardening practices
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-14 | $17.73 |
| 15-29 | $15.50 |
| 30-89 | $12.40 |
| 90+ | $11.28 |
CPO-4250 has a 4.25 in diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.
ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.
- Extremely smooth surface finish
- Excellent wear and corrosion resistance
- Good strength and impact properties
- Good machinability
- Reasonable weldability
- Fair response to normal heat treating and induction hardening practices
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-14 | $21.34 |
| 15-29 | $18.65 |
| 30-59 | $16.56 |
| 60+ | $13.58 |
