Search Results

A heavy duty double-acting assembly, the capped piston T-seal exhibits excellent sealability, extrusion resistance, and wearability. T-seals with “BR” suffix utilize a Bronze Filled PTFE cap instead of the standard Glass Filled PTFE cap.

PTFE; Nylon; Rubber Material | 4.27 in Nominal Inner Diameter | Capped Piston T-Seal

Features

• Glass-filled PTFE cap, nylon back-up, rubber energizer

These lip-type buffer seals are designed for replacement in Caterpillar® cylinders. The hinged-lip design reduces friction, heat, and wear under low-pressure conditions and acts as a check valve allowing back-pressure relief. Seals for rod sizes 2-1/8” and under do not have a back-up ring.

Urethane Material | 2 1/2 in Nominal Inner Diameter | Buffer Seal

These seals are specifically designed to seal on their inside diameter and engineered to attain maximum life and reliability in dynamic rod sealing.

92A Durometer | Urethane Material | 1 3/4 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal

HT-14000X12000CDS has a wall thickness of 1 in. The ID is 12 in and the OD is 14 in. The material is CDSM 1026 Carbon Steel and has been stress-relieved and annealed.

This tube has been produced using the cold drawing process and is seamless. The cold drawing process produces higher physical properties without additional heat treating resulting in good strength to weight ratios.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

Suffix “V” designates fluorocarbon material,“N” designates nitrile material, and “HT” designates high temperature urethane.

90A Durometer | Urethane Material | 1 1/4 in Nominal Inner Diameter

Features

• Urethane Wiper Ring
• Min. Temperature Range of ‘-40 °F; N: -40°; V: -20 °F; HT: -40 °F
• Max. Temperature Range of 200 °F; N: 225 °F; V: 350 °F; HT: 225 °F

Suffix “V” designates fluorocarbon material,“N” designates nitrile material, and “HT” designates high temperature urethane.

90A Durometer | Urethane Material | 1 3/4 in Nominal Inner Diameter

Features

• Urethane Wiper Ring
• Min. Temperature Range of ‘-40 °F; N: -40°; V: -20 °F; HT: -40 °F
• Max. Temperature Range of 200 °F; N: 225 °F; V: 350 °F; HT: 225 °F

Suffix “V” designates fluorocarbon material,“N” designates nitrile material, and “HT” designates high temperature urethane.

90A Durometer | Urethane Material | 4 in Nominal Inner Diameter

Features

• Urethane Wiper Ring
• Min. Temperature Range of ‘-40 °F; N: -40°; V: -20 °F; HT: -40 °F
• Max. Temperature Range of 200 °F; N: 225 °F; V: 350 °F; HT: 225 °F

5.5 in induction hardened chrome shafting.

The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).

Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.

• Greater strength
• Better resistance to mechanical damage

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

Molded in PTFE with a rubber energizer, this seal absorbs the shock of pressure spikes to protect the rod seal. Bronze-filled Teflon rod buffer seal with a rubber energizer.

Bronze Filled PTFE Material | 4 1/2 in Nominal Inner Diameter | Buffer Seal

Molded in PTFE with a rubber energizer, this seal absorbs the shock of pressure spikes to protect the rod seal. Bronze-filled Teflon rod buffer seal with a rubber energizer.

Bronze Filled PTFE Material | 6 in Nominal Inner Diameter | Buffer Seal