Search Results
Filter Your Search
Category Group
Shop by Category
The PS1800 provides low friction, high strength piston sealing. The PS1800 also provides double-acting piston sealing in a compact design that meets the requirements of ANSI/B93-32-1973. Piston diameter “I” dimensions are given for pistons without wear rings.
15% Glass Filled PTFE Material | 2 3/16 in Nominal Inner Diameter | Piston Seal
Features
- Easy assembly
- Low friction capabilities
Molded from a PTFE base material with 40% bronze and machined to exacting tolerances, this seal exhibits low friction and high strength corners are chamfered for cold flow resistance.
40% Bronze Filled PTFE Material | 5 5/32 in Nominal Inner Diameter | Piston Seal
Features
- Easy assembly
- Low friction capabilities
Style ST wiper rings are precision molded from 90A durometer urethane. Flexible enough to easily snap into a groove yet tough enough to handle difficult rod wiping applications. “V” tagged wipers are constructed of fluorocarbon.
90A Durometer | Urethane Material | 5 1/4 in Nominal Inner Diameter
Features
- Flexible enough to snap into a groove
- Wipers are constructed of fluorocarbon
Featuring high pressure and high shock load capability, this seal utilizes the same twin lip design found in Hercules®, Sealing Products’ RTU style. With the main body of the seal molded from high performance polyurethane, this seal, incorporates a dynamically designed nitrile energizer and a tough polyacetal anti-extrusion ring. RTUB is capable of, pressures up to 10,000 psi in approved applications. Please consult Hercules Engineering for pressures above 6,000, psi.
The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland. The unique profile of the NBR energizer ensures the primary sealing lips maintain contact under low or no pressure situations while ensuring proper sealing at higher pressures. The Hallite 621 also incorporates an acetyl anti-extrusion ring to withstand side loads and extreme pressure peaks even with the extrusion gaps.
94A Durometer | Urethane Material | 1 3/4 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal
The Z-Seal™ is a squeeze type seal, combining the excellent sealability and low compression set of a resilient rubber lip with the greater anti-extrusion characteristics of a hard thermoplastic base. Under low pressure conditions, the sealing lip provides its own compressive seal force. As pressure increases, hydrostatic pressure is mechanically transmitted through the elastomeric seal element into the anti-extrusion base. The applied force then deflects radially in a controlled manner, closing the extrusion gap behind the sealing lip. Under this condition, maximum sealing effectiveness is achieved.
95A 70A Durometer | Urethane Nitrile Rubber Material | 5 1/2 in Nominal Inner Diameter | 3/8 in Cross Section | Z-Seal
Solid Urethane backup ring with a flat cross-section.
95A Durometer | Urethane Material | 4 1/8 in Nominal Inner Diameter | 3/16 in Cross Section | Backup Ring
Features
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
Molded in a tough urethane, this rod u-seal fits tightly in the groove while providing increased radial force on the rod.
Urethane Material | 36 MM Nominal Inner Diameter | Rod U-Seal
Cast Iron Rod Clevis Mount with a 2.25 in – 12 TPI threaded end and a 2.5 in pin hole.
Clevis mounts help maintain alignment and protect the cylinder from side load. Mounts attach to threaded stud ends, pivot holes, or bolt holes on the cylinder. Can be used with hydraulic cylinders with standard bore sizes.
Cast Iron Rod Clevis Mount with a 1 in – 14 TPI threaded end and a 1 in pin hole.
Clevis mounts help maintain alignment and protect the cylinder from side load. Mounts attach to threaded stud ends, pivot holes, or bolt holes on the cylinder. Can be used with hydraulic cylinders with standard bore sizes.
