Search Results
Filter Your Search
Category Group
Shop by Category
CPO-5500 has a 5.5 in diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.
ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.
- Extremely smooth surface finish
- Excellent wear and corrosion resistance
- Good strength and impact properties
- Good machinability
- Reasonable weldability
- Fair response to normal heat treating and induction hardening practices
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-14 | $68.00 |
| 15-29 | $48.62 |
| 30-59 | $42.50 |
| 60-119 | $34.00 |
| 120+ | $30.94 |
A heavy duty double-acting assembly, the capped piston T-seal exhibits excellent sealability, extrusion resistance, and wearability. T-seals with “BR” suffix utilize a Bronze Filled PTFE cap instead of the standard Glass Filled PTFE cap.
PTFE; Nylon; Rubber Material | 3.52 in Nominal Inner Diameter | Capped Piston T-Seal
Features
- Glass-filled PTFE cap, nylon back-up, rubber energizer
Used interchangeably for piston or rod sealing, these u-seals employ the same tough urethane material found in our, Heavy Duty Rod and Piston U-Seals.
92A Durometer | Urethane Material | 1 1/4 in Nominal Inner Diameter | 1/8 in Cross Section | U-Seal
5 in induction hardened chrome shafting.
The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).
Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.
- Greater strength
- Better resistance to mechanical damage
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-14 | $46.79 |
| 15-29 | $33.45 |
| 30-59 | $29.24 |
| 60-119 | $23.39 |
| 120+ | $21.29 |
HT-11000X10000 has a wall thickness of 0.5 in. The ID is 10 in and the OD is 11 in. The material is DOM 1026 Carbon Steel and has been stress-relieved and annealed.
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-14 | $31.10 |
| 15-59 | $25.50 |
| 60+ | $23.40 |
Suffix “V” designates fluorocarbon material,“N” designates nitrile material, and “HT” designates high temperature urethane.
90A Durometer | Urethane Material | 2 1/2 in Nominal Inner Diameter
Features
- Urethane Wiper Ring
- Min. Temperature Range of ‘-40 °F; N: -40°; V: -20 °F; HT: -40 °F
- Max. Temperature Range of 200 °F; N: 225 °F; V: 350 °F; HT: 225 °F
O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.
70A Durometer | Nitrile Material | 45 MM Nominal Inner Diameter | 3 MM Cross Section | O-Ring
Features
- Chemical resistance
- Temperature range of -40 °F to 220 °F
Molded from filled PTFE and machined to close tolerances, these seals feature low friction and excellent wear characteristics. Nitrile rings are used for energizers.
70A Durometer | PTFE Material | 37 MM Nominal Inner Diameter | Piston Seal
Features
- Easy assembly
- Low friction capabilities
Designed to fit on one or two piece pistons, this piston seal employs a nitrile seal for high sealability, nylon split back-ups for extrusion resistance, and two split bearing rings. No further support bearings are required.
70A Durometer | NBR Material | 54 MM Nominal Inner Diameter | Piston Seal
Features
- Easy assembly
- Low friction capabilities
Style 850 u-seals offer excellent resistance to extrusion and abrasion. The round cross-section expander offers energized sealing from zero to 5,000 psi.
95A Durometer | Urethane Material | 2 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal
