Wipers

Single-lipped, snap-in rod wiper is designed to fit D-style housings.

The ST-XLF wipers are designed to fit the standard ST wiper groove. These wipers include a dust lip to prevent contaminates from entering through the groove. They also have a ribbed inside diameter for low friction operation and to prevent pressure traps between the wiper and rod seal. Developed specifically for use in harsher environments with heavy contamination, such as in agriculture, off-highway, and forestry equipment.

Urethane Material | 1 3/8 in Nominal Inner Diameter

Features

• Precision trimmed wiping lip
• Retrofits most ‘D’ wiper housings
• Especially effective in vertically mounted cylinders
• Designed to follow the rod deflection caused by side loads
• Interchangeable with Hallite 520 wiper
• Sharp wiping lip scrapes heavy contamination from rod protecting sealing system
• Umbrella Wiper Technology™ protects housing from contamination and reduces moisture ingress

STXE wipers are designed to retrofit the standard ST wiper groove while providing superior performance. The o-ring energizer limits dirt intrusion around the OD of the wiper. The energizer also makes this wiper more effective in applications with severe side deflections.

Urethane Material | 2 1/2 in Nominal Inner Diameter

Features

• Designed to retrofit the standard ST wiper groove
• O-ring energizer limits dirt intrusion around the OD of the wiper

Wipers are installed in hydraulic cylinders to prevent dirt, dust, and moisture from entering the cylinder as they retract back into the system. A hydraulic wiper prevents contamination that could damage wear rings, seals, and other cylinder components.

90A Durometer | Urethane Material | 2 in Nominal Inner Diameter

Features

• Installed in hydraulic cylinders to prevent dirt, dust, and moistures
• Hydraulic wiper prevents contamination that could damage wear rings, seals, and other cylinder components

Suffix “SH” designates slotted heel design, “V” designates fluorocarbon material, and “B” designates carboxilated nitrile material.

90A Durometer | Urethane Material | 2 in Nominal Inner Diameter

Features

• Slotted heel design
• Slots in the heel allow excess hydraulic fluid to bypass the wiper

AN wipers are ideal for light duty and pneumatic applications. Its main purpose is to prevent dirt and contaminants from entering the hydraulic or pneumatic systems.

AN wipers will retrofit into glands prescribed in MS-33675 for corresponding dash numbers of MS-28776.

• Flexible, snap-in design for easy installation into closed housings
• Low compression set

AN wipers are ideal for light duty and pneumatic applications. Its main purpose is to prevent dirt and contaminants from entering the hydraulic or pneumatic systems. Suffix “SH” designates slotted heel design, “V” designates fluorocarbon material, and “B” designates carboxilated nitrile material.

90A Durometer | Urethane Material | 7 in Nominal Inner Diameter

Features

• Flexible, snap-in design for easy installation into closed housings
• Low compression set

Utilizing a double lip of urethane bonded to a carbon steel case, this wiper prevents contaminant ingression at the wiping lip and around the outer case.

Urethane Material | 95 MM Nominal Inner Diameter | Wiper

Rubber Material | 1 7/8 in Nominal Inner Diameter | Wiper

Rubber Material | 1 7/8 in Nominal Inner Diameter | Wiper

Rubber Material | 2 in Nominal Inner Diameter | Wiper

Rubber Material | 2 in Nominal Inner Diameter | Wiper

Utilizing a sturdy metal case, these wipers are molded from the same high performance urethane used in our Heavy Duty U-seals. Built for severe service, these wipers are capable of surviving hostile environments.

92A Durometer | Urethane Material | 3 in Nominal Inner Diameter

Features

• Used in Heavy Duty U-seals
• Capable of surviving hostile environments
• Molded from the high performance urethane