Search Results
Filter Your Search
Category Group
Shop by Category
Wear rings provide a hard-wearing surface that protects the cylinder walls and the piston rod from scoring and abrasion. By maintaining alignment and reducing side loads, these rings facilitate smoother piston movement and lower friction levels.
Nylon Material | 2 3/4 in Nominal Inner Diameter | 1/8 in Cross Section | Wear Ring
Features
- Protection Against Wear
- Reduced Friction
- Extended Cylinder Life
- Operational Efficiency
Wear rings provide a hard-wearing surface that protects the cylinder walls and the piston rod from scoring and abrasion. By maintaining alignment and reducing side loads, these rings facilitate smoother piston movement and lower friction levels.
Nylon Material | 3 in Nominal Inner Diameter | 1/8 in Cross Section | Wear Ring
Features
- Protection Against Wear
- Reduced Friction
- Extended Cylinder Life
- Operational Efficiency
Parback® backup ring with a curved cross-section.
Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.
90A Durometer | Buna-N Rubber Material | 7 3/4 in Nominal Inner Diameter | 1/4 in Cross Section | Backup Ring
Features
- Excellent extrusion resistance
- Easily stretched for installation
- Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces
Parback® backup ring with a curved cross-section.
Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.
90A Durometer | Buna-N Rubber Material | 11 1/2 in Nominal Inner Diameter | 1/4 in Cross Section | Backup Ring
Features
- Excellent extrusion resistance
- Easily stretched for installation
- Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces
Parback® backup ring with a curved cross-section.
Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.
90A Durometer | Buna-N Rubber Material | 12 in Nominal Inner Diameter | 1/4 in Cross Section | Backup Ring
Features
- Excellent extrusion resistance
- Easily stretched for installation
- Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces
Parback® backup ring with a curved cross-section.
Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.
90A Durometer | Buna-N Rubber Material | 13 1/2 in Nominal Inner Diameter | 1/4 in Cross Section | Backup Ring
Features
- Excellent extrusion resistance
- Easily stretched for installation
- Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces
Wear rings provide a hard-wearing surface that protects the cylinder walls and the piston rod from scoring and abrasion. By maintaining alignment and reducing side loads, these rings facilitate smoother piston movement and lower friction levels.
Nylon Material | 3 5/8 in Nominal Inner Diameter | 1/8 in Cross Section | Wear Ring
Features
- Scarf Cut wear ring
- Protection Against Wear
- Reduced Friction
- Extended Cylinder Life
- Operational Efficiency
Solid Teflon backup ring with a flat cross-section.
PTFE can withstand high temperatures and is compatible with nearly all fluids.
PTFE Material | 1/4 in Nominal Inner Diameter | 1/16 in Cross Section | Backup Ring
Features
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
- Deals very well with surface wear
5/16 X 1/2 Back-up SOLID PTFE
2 X 2 3/16 Back-up SOLID PTFE
