Browse Categories

Search Results

Filter Your Search

Show Attribute Category Group

Shop by Category

Loading...

Fabricated from fine woven fabric and phenolic resins, this wear ring is strong yet light weight with an excellent wear rate.

Phenolic Material | 135 MM Nominal Inner Diameter | Wear Ring

Features

  • Protection Against Wear
  • Reduced Friction
  • Extended Cylinder Life
  • Operational Efficiency

$32.41
/EA

Style 850 u-seals offer excellent resistance to extrusion and abrasion. The round cross-section expander offers energized sealing from zero to 5,000 psi.

95A Durometer | Urethane Material | 1 1/4 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal

$7.47
/EA

Asymmetric rod seal designed with precision trimmed sealing lips to provide a dry sealing solution in light and medium-duty applications. The Hallite 605 is molded in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation and excellent low temperature performance. The twin lip design helps solve difficult rod sealing problems by providing lower friction, increased stability, and high, dynamic lip force, while preventing air penetration from outside the cylinder. Designed to have interference in the seal housing groove and has a secondary lip. The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland. The inner dynamic lip is shorter and more robust to improve sealing and compression set characteristics over conventional, symmetrical U-seals.

The seal can be considered for use in heavy-duty applications when used with a suitable full depth back-up ring. The sealing lips are precision trimmed at an angle to give optimal rod sealing performance.

94A Durometer | Urethane Material | 1 3/8 in Nominal Inner Diameter | 1/8 in Cross Section | U-Seal

Features

  • General purpose rod seal
  • Robust design
  • Excellent wear resistance
  • Increase seal stability
  • Performs well over wide temperature range and is extremely effective in low temperatures
  • Primary lip protection
  • Easy to install

$9.05
/EA

TR-875 has a 0.875 in diameter. The material is 1144 Carbon Steel, which is equivalent to Stressproof tie rod.

Tie rods are sold in 12 ft. lengths only. Rods can be cut for UPS shipment or left whole, if necessary. Freight charges may vary depending on required length.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

$97.85
/EA

Parback® backup ring with a curved cross-section.

Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.

90A Durometer | Buna-N Rubber Material | 7 1/2 in Nominal Inner Diameter | 1/4 in Cross Section | Backup Ring

Features

  • Excellent extrusion resistance
  • Easily stretched for installation
  • Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces

$8.75
/EA

Parback® backup ring with a curved cross-section.

Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.

90A Durometer | Buna-N Rubber Material | 9 1/2 in Nominal Inner Diameter | 1/4 in Cross Section | Backup Ring

Features

  • Excellent extrusion resistance
  • Easily stretched for installation
  • Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces

$9.03
/EA

Wear rings provide a hard-wearing surface that protects the cylinder walls and the piston rod from scoring and abrasion. By maintaining alignment and reducing side loads, these rings facilitate smoother piston movement and lower friction levels.

Nylon Material | 2 3/4 in Nominal Inner Diameter | 1/8 in Cross Section | Wear Ring

Features

  • Scarf Cut wear ring
  • Protection Against Wear
  • Reduced Friction
  • Extended Cylinder Life
  • Operational Efficiency

$9.95
/EA

GB-TFE-1/2×1/8-C/S

$44.16
/FT

Molded in PTFE with a rubber energizer, this seal absorbs the shock of pressure spikes to protect the rod seal. Bronze-filled Teflon rod buffer seal with a rubber energizer.

Bronze Filled PTFE Material | 3 1/2 in Nominal Inner Diameter | Buffer Seal

$42.30
/EA

This capped piston seal consists of a filled PTFE cap, a T-shaped NBR energizer, and two split nylon backup rings. It exhibits low friction, high sealability, and excellent resistance to extrusion and wear.

PTFE Material | 100 MM Nominal Inner Diameter | Piston Seal

Features

  • Easy assembly
  • Low friction capabilities

$74.35
/EA
  • « PREV
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • NEXT »