Search Results

Suffix “V” designates fluorocarbon material,“N” designates nitrile material, and “HT” designates high temperature urethane.

90A Durometer | Urethane Material | 1 3/8 in Nominal Inner Diameter

Features

• Urethane Wiper Ring
• Min. Temperature Range of ‘-40 °F; N: -40°; V: -20 °F; HT: -40 °F
• Max. Temperature Range of 200 °F; N: 225 °F; V: 350 °F; HT: 225 °F

Designed to fit on one or two piece pistons, this piston seal employs a nitrile seal for high sealability, nylon split back-ups for extrusion resistance, and two split bearing rings. No further support bearings are required.

70A Durometer | NBR Material | 60 MM Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities

ALUM-5000 has a 5 in diameter. The material is 6061 Aluminum T6

6061 Aluminum T6 is suitable for machining pistons and head glands.

The T6 refers to the temper or degree of hardness. T6 has been solution heat treated and artificially aged to provide the maximum yield strength for a 6061 aluminum alloy.

• Heat treated and aged for increased strength
• Easily formed
• Weldable
• Corrosion resistant

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

110mm induction hardened chrome shafting.

The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).

Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.

• Greater strength
• Better resistance to mechanical damage

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

Rubber Material | 1 in Nominal Inner Diameter | Wiper

Rubber Material | 1 in Nominal Inner Diameter | Wiper

Rubber Material | 1 3/8 in Nominal Inner Diameter | Wiper

Rubber Material | 1 3/8 in Nominal Inner Diameter | Wiper

Totally interchangeable with Style PS1400 PTFE piston seals, Style PS1500 piston seals are molded from tough 60 Shore D durometer polyurethane. During the molding process, a .002” thick band of molybdenum disulfide is molded into the outside diameter of the seal ring for reduced friction. PS1500 piston seals are easily stretched over the piston and recover rapidly with the elimination of the “cold flow” characteristics found in PTFE seals. Piston diameter “I” dimensions are given for pistons without wear rings.

60 Shore D Durometer | Polyurethane Material | 3.606 in Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities

The Style PSC is a double acting piston seal designed to replace o-rings, quad-rings, and T-seals with the same groove dimensions (O-ring dash number). Style 575 urethane back-up rings may be added to either or both sides of the “PSC” to accommodate wider groove widths. The PSC is made of 95A Durometer polyurethane, giving it high extrusion and abrasion resistance. The crowned sealing surface produces a positive seal from vacuum to high pressure. Hercules® Sealing Products also offers a wide base (WB) Style PSC piston seal. These wide base seals have the same characteristics of the standard PSC seals but offer a wider base, eliminating the need to use back-up rings to accommodate wider grooves. Piston diameter “I” dimensions are given for piston without wear rings.

95A; 70A Durometer | Polyurethane Material | 3 5/8 in Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities

US-90URE-1-1/4×1-5/8×5/16

*
5 in Hot Finished 1018 Carbon Steel*
round bar. Material can be cut to any size.

Suitable for shafting and applications that do not require the greater strength of high carbon and alloy steels.

• Good case hardening properties
• Fair machinability
• Readily brazed and welded

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.