Wipers

Suffix “V” designates fluorocarbon material,“N” designates nitrile material, and “HT” designates high temperature urethane.

90A Durometer | Urethane Material | 1 3/4 in Nominal Inner Diameter

Features

• Urethane Wiper Ring
• Min. Temperature Range of ‘-40 °F; N: -40°; V: -20 °F; HT: -40 °F
• Max. Temperature Range of 200 °F; N: 225 °F; V: 350 °F; HT: 225 °F

Utilizing a sturdy metal case, these wipers are molded from the same high performance urethane used in our Heavy Duty U-seals. Built for severe service, these wipers are capable of surviving hostile environments.

92A Durometer | Urethane Material | 2 3/4 in Nominal Inner Diameter

Features

• Used in Heavy Duty U-seals
• Capable of surviving hostile environments
• Molded from the high performance urethane

Style AN-M2 scrapers conform to MS28776-M2 sizes and are manufactured in brass. The scrapers are suitable for extreme environments with aggressive contaminants. The unique spring-loaded construction and ductile material result in close rod contact even when coping with rod ovality and helix grinding patterns.

Brass Material | 2 1/4 in Nominal Inner Diameter

Features

• Scrapers are suitable for extreme environments with aggressive contaminants
• Unique spring-loaded construction
• Manufactured in brass

RW-90FKM-2-1/4×2.552×0.104

Each Seal Guard Wiper consists of two flexible bronze rings which are held in place by a nitrile cushion ring. The cushion ring absorbs side loads and energizes the wiper to maintain close contact with the rod. Particularly suited for hostile environments, seal guard wipers shave off sand, grift, slag, flux, paint, moisture, chips and slivers. Seal Guard Wipers are long-lasting, self-adjusting, and offer low friction. Seal Guard Wipers can be installed in standard Hercules® Sealing Products “ST” or “D” Style grooves by increasing the “F” gland dimension to the “F” Throat Diameter shown.

70A Durometer | 660 Bronze; Nitrile Material | 3 1/2 in Nominal Inner Diameter | Wiper

AN wipers are ideal for light duty and pneumatic applications. Its main purpose is to prevent dirt and contaminants from entering the hydraulic or pneumatic systems. Suffix “SH” designates slotted heel design, “V” designates fluorocarbon material, and “B” designates carboxilated nitrile material.

90A Durometer | Urethane Material | 5/8 in Nominal Inner Diameter

Features

• Flexible, snap-in design for easy installation into closed housings
• Low compression set

Style ST wiper rings are precision molded from 90A durometer urethane. Flexible enough to easily snap into a groove yet tough enough to handle difficult rod wiping applications. “V” tagged wipers are constructed of fluorocarbon.

90A Durometer | Urethane Material | 1 3/8 in Nominal Inner Diameter

Features

• Flexible enough to snap into a groove
• Wipers are constructed of fluorocarbon

Rubber Material | 1 1/8 in Nominal Inner Diameter | Wiper

Rubber Material | 1 1/8 in Nominal Inner Diameter | Wiper

Style AN-M2 scrapers conform to MS28776-M2 sizes and are manufactured in brass. The scrapers are suitable for extreme environments with aggressive contaminants. The unique spring-loaded construction and ductile material result in close rod contact even when coping with rod ovality and helix grinding patterns.

Brass Material | 4 1/2 in Nominal Inner Diameter

Features

• Scrapers are suitable for extreme environments with aggressive contaminants
• Unique spring-loaded construction
• Manufactured in brass

This wiper is a single lip design molded from high grade nitrile and bonded to a carbon steel case.

Nitrile Material | 40 MM Nominal Inner Diameter | Wiper