Mobile Equipment Seal Kits

The Z-Seal™ is a squeeze type seal, combining the excellent sealability and low compression set of a resilient rubber lip with the greater anti-extrusion characteristics of a hard thermoplastic base. Under low pressure conditions, the sealing lip provides its own compressive seal force. As pressure increases, hydrostatic pressure is mechanically transmitted through the elastomeric seal element into the anti-extrusion base. The applied force then deflects radially in a controlled manner, closing the extrusion gap behind the sealing lip. Under this condition, maximum sealing effectiveness is achieved.

95A 70A Durometer | Urethane Nitrile Rubber Material | 1 1/2 in Nominal Inner Diameter | 3/16 in Cross Section | Z-Seal

Asymmetric rod seal designed with precision trimmed sealing lips to provide a dry sealing solution in light and medium-duty applications.

The Hallite 605 is molded in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation and excellent low temperature performance.

Designed to have interference in the seal housing groove and has a secondary lip. The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland.

The inner dynamic lip is shorter and more robust to improve sealing and compression set characteristics over conventional, symmetrical U-seals.

The seal can be considered for use in heavy-duty applications when used with a suitable full depth back-up ring. The sealing lips are precision trimmed at an angle to give optimal rod sealing performance.

• General purpose rod seal
• Robust design
• Excellent wear resistance
• Increase seal stability
• Performs well over wide temperature range and is extremely effective in low temperatures
• Primary lip protection
• Easy to install

Featuring high pressure and high shock load capability, this seal utilizes the same twin lip design found in Hercules®, Sealing Products’ RTU style. With the main body of the seal molded from high performance polyurethane, this seal, incorporates a dynamically designed nitrile energizer and a tough polyacetal anti-extrusion ring. RTUB is capable of, pressures up to 10,000 psi in approved applications. Please consult Hercules Engineering for pressures above 6,000, psi.

The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland. The unique profile of the NBR energizer ensures the primary sealing lips maintain contact under low or no pressure situations while ensuring proper sealing at higher pressures. The Hallite 621 also incorporates an acetyl anti-extrusion ring to withstand side loads and extreme pressure peaks even with the extrusion gaps.

94A Durometer | Urethane Material | 3 1/4 in Nominal Inner Diameter | 1/4 in Cross Section | U-Seal

Utilizing the same profiles as the Style 800 Polyurethane U-Seal line, these u-seals are molded from a fluorocarbon, compound. While being compatible with a broader range of fluids, these fluorocarbon seals will also operate, continuously at temperatures from -20° to +400 °F. NOTE: If you are not sure of fluid/seal compatibility, please refer, to the fluid compatibility chart in the appendix or contact our Engineering Department.

95A Durometer | Fluorocarbon Material | 2 1/2 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal

US-90URE-3-1/4×3-5/8×3/8

US-90URE-3-1/2×3-7/8×3/8

US-90URE-3×3-7/16×7/32

Incorporating a rubber seal lip, a rubberized fabric heel, and an acetal back-up ring, this seal provides excellent sealability and high extrusion resistance.

80 Durometer | NBR Material | 25 MM Nominal Inner Diameter | Rod U-Seal

The twin lip design helps solve difficult rod sealing problems by providing lower friction, increased stability, and high, dynamic lip force, while preventing air penetration from outside the cylinder.

Asymmetric rod seal designed with precision trimmed sealing lips to provide a dry sealing solution in light and medium-duty applications. The Hallite 605 is molded in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation and excellent low temperature performance.

Designed to have interference in the seal housing groove and has a secondary lip. The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland. The inner dynamic lip is shorter and more robust to improve sealing and compression set characteristics over conventional, symmetrical U-seals. The seal can be considered for use in heavy-duty applications when used with a suitable full depth back-up ring. The sealing lips are precision trimmed at an angle to give optimal rod sealing performance.

94A Durometer | Urethane Material | 2 1/2 in Nominal Inner Diameter | 5/16 in Cross Section | U-Seal

Features

• General purpose rod seal
• Robust design
• Excellent wear resistance
• Increase seal stability
• Performs well over wide temperature range and is extremely effective in low temperatures
• Primary lip protection
• Easy to install

These seals are specifically designed to seal on their inside diameter and engineered to attain maximum life and reliability in dynamic rod sealing.

92A Durometer | Urethane Material | 1 1/8 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal