Mobile Equipment Seal Kits
Search in Category
Filter Your Search
Category Group
Durometer
Material
Nominal Height
Nominal Inner Diameter
Nominal Outer Diameter
Style
Unit of Measure
Shop by Category
Asymmetric rod seal designed with precision trimmed sealing lips to provide a dry sealing solution in light and medium-duty applications. The Hallite 605 is molded in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation and excellent low temperature performance. The twin lip design helps solve difficult rod sealing problems by providing lower friction, increased stability, and high, dynamic lip force, while preventing air penetration from outside the cylinder. Designed to have interference in the seal housing groove and has a secondary lip. The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland. The inner dynamic lip is shorter and more robust to improve sealing and compression set characteristics over conventional, symmetrical U-seals.
The seal can be considered for use in heavy-duty applications when used with a suitable full depth back-up ring. The sealing lips are precision trimmed at an angle to give optimal rod sealing performance.
94A Durometer | Urethane Material | 2 1/8 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal
Features
- General purpose rod seal
- Robust design
- Excellent wear resistance
- Increase seal stability
- Performs well over wide temperature range and is extremely effective in low temperatures
- Primary lip protection
- Easy to install
Asymmetric rod seal designed with precision trimmed sealing lips to provide a dry sealing solution in light and medium-duty applications. The Hallite 605 is molded in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation and excellent low temperature performance. The twin lip design helps solve difficult rod sealing problems by providing lower friction, increased stability, and high, dynamic lip force, while preventing air penetration from outside the cylinder. Designed to have interference in the seal housing groove and has a secondary lip. The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland. The inner dynamic lip is shorter and more robust to improve sealing and compression set characteristics over conventional, symmetrical U-seals.
The seal can be considered for use in heavy-duty applications when used with a suitable full depth back-up ring. The sealing lips are precision trimmed at an angle to give optimal rod sealing performance.
94A Durometer | Urethane Material | 2 3/8 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal
Features
- General purpose rod seal
- Robust design
- Excellent wear resistance
- Increase seal stability
- Performs well over wide temperature range and is extremely effective in low temperatures
- Primary lip protection
- Easy to install
The Z-Seal™ is a squeeze type seal, combining the excellent sealability and low compression set of a resilient rubber lip with the greater anti-extrusion characteristics of a hard thermoplastic base. Under low pressure conditions, the sealing lip provides its own compressive seal force. As pressure increases, hydrostatic pressure is mechanically transmitted through the elastomeric seal element into the anti-extrusion base. The applied force then deflects radially in a controlled manner, closing the extrusion gap behind the sealing lip. Under this condition, maximum sealing effectiveness is achieved.
70A Durometer | Nitrile Rubber Material | 1 3/8 in Nominal Inner Diameter | 3/16 in Cross Section | Z-Seal
Asymmetric rod seal designed with precision trimmed sealing lips to provide a dry sealing solution in light and medium-duty applications. The Hallite 605 is molded in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation and excellent low temperature performance. The twin lip design helps solve difficult rod sealing problems by providing lower friction, increased stability, and high, dynamic lip force, while preventing air penetration from outside the cylinder. Designed to have interference in the seal housing groove and has a secondary lip. The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland. The inner dynamic lip is shorter and more robust to improve sealing and compression set characteristics over conventional, symmetrical U-seals.
The seal can be considered for use in heavy-duty applications when used with a suitable full depth back-up ring. The sealing lips are precision trimmed at an angle to give optimal rod sealing performance.
94A Durometer | Urethane Material | 2 3/4 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal
Features
- General purpose rod seal
- Robust design
- Excellent wear resistance
- Increase seal stability
- Performs well over wide temperature range and is extremely effective in low temperatures
- Primary lip protection
- Easy to install
Style 800 U-seals are molded from tough, abrasion-resistant polyurethane. The four lobed expander ring energizes the, sealing lips, even at zero pressure, to help prevent “weeping” when the system is idle.
95A Durometer | Urethane Material | 1 1/2 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal
Utilizing the same profiles as the Style 800 Polyurethane U-Seal line, these u-seals are molded from a fluorocarbon, compound. While being compatible with a broader range of fluids, these fluorocarbon seals will also operate, continuously at temperatures from -20° to +400 °F. NOTE: If you are not sure of fluid/seal compatibility, please refer, to the fluid compatibility chart in the appendix or contact our Engineering Department.
95A Durometer | Fluorocarbon Material | 1 5/8 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal
Our Style 800 orange Hytrel U-seals offer superior resistance to abrasion, extrusion, and heat. As a drop-in replacement, for our standard Style 800 U-seals, they can prolong equipment life under today’s increased demands. These seals are, suitable for both petroleum-based and water-based fluids.
55D Durometer | Hytrel Material | 1 3/4 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal
